601917
31
Zoom out
Zoom in
Previous page
1/44
Next page
Various settings
31
It
De
3. Hardware
Speaker Impedance:
If any of the connected speakers
have 4
h
or more to less than 6
h
impedance, or if you
have connected a different set of left and right speakers
to the SPEAKERS A/B terminals, set the impedance to
4
h
.
0
Reduce the volume to minimum before setting.
6h
(default setting)
4h
Auto Standby:
The unit will automatically enter standby
mode if there is no operation for 20 minutes with no audio
signal input.
On
(default setting)
Off
Network Standby:
you can turn on the power of the unit
via network using an application such as Onkyo Remote.
On
Off
(default setting)
0
When “Network Standby” is used, the power
consumption increases even when the unit is on
standby. However, the increase in power consumption
is kept to a minimum by automatically entering the
HYBRID STANDBY mode, where only the essential
circuit is operating.
0
If it is not displayed, wait for a moment until the
network feature starts.
Opt1 In Wakeup:
When an audio signal is input through
the OPTICAL terminal while this unit is in standby, this
feature automatically detects it.
Off
(default setting)
On
: This unit is turned on and outputs the audio.
0
When a cable is connected to the OPTICAL terminal
and this setting is enabled, power consumption
increases even when the unit is on standby, however,
the increase in power consumption is kept to a
minimum by automatically entering the HYBRID
STANDBY mode, where only essential circuits are
operating.
AM Freq Step:
Changes the AM radio frequency step.
9kHz
(default setting): The frequency is adjusted in
increments of 9 kHz.
10kHz
: The frequency is adjusted in increments of
10 kHz.
4. Source
IntelliVolume:
Even when the volume control is the same
on this unit, there may be differences in the volume
depending on the connected devices. Adjust this when
you want to alleviate this difference. To set, select each
input source.
j12 dB
to
i12 dB
(default setting: 0 dB)
Name Edit:
Enter a simple name of up to 10 characters
in length for the input sources or preset AM/FM stations.
To set, select each input source or select the preset
number of the registered station.
0
For information on how to input characters, see
“Inputting characters” (
>
30).
5. Network
Make the network setting.
0
If it is not displayed, wait for a moment until the
network feature starts.
0
When LAN is configured with a DHCP, set “DHCP” to
“Enable” to configure the setting automatically.
(“Enable” is set by default) To assign fixed IP
addresses to each components, you must set “DHCP”
to “Disable” and assign an address to this unit in “IP
Address” as well as set information related to your
LAN, such as Subnet Mask and Gateway.
MAC Address:
View this unit’s MAC address.
DHCP:
Enable
(default setting)
Disable
IP Address:
View/set the IP address.
Subnet Mask:
View/set the subnet mask.
Gateway:
View/set the default gateway.
DNS Server:
View/set the DNS server address.
Proxy URL:
Set the proxy server address.
Proxy Port:
Set the proxy port number.
0
This only appears when Proxy URL has been set.
Friendly Name:
Change the name for this unit to a
simple one for display on the equipment connected by
network. Press the ENTER button and input 31 or less
characters.
0
For information on how to input characters, see
“Inputting characters” (
>
30).
Network Check:
You can check the network connection.
Press the ENTER button when “Start” is displayed.
TX-8130_mst.book 31 ページ 2015年6月9日 火曜日 午後5時20分
31


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-8130 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-8130 in the language / languages: English as an attachment in your email.

The manual is 2,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-8130

Onkyo TX-8130 User Manual - German - 80 pages

Onkyo TX-8130 User Manual - Dutch - 80 pages

Onkyo TX-8130 User Manual - French - 80 pages

Onkyo TX-8130 User Manual - Italian - 80 pages

Onkyo TX-8130 User Manual - Swedish - 80 pages

Onkyo TX-8130 User Manual - Spanish - 80 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info