462129
51
Zoom out
Zoom in
Previous page
1/56
Next page
En-51
Troubleshooting
If you have any trouble using the receiver, look for a
solution in this section.
Can’t turn on the receiver
Make sure that the power cord is plugged into the
electric outlet properly.
Unplug the power cord from the electric outlet, wait 5
seconds or more, then plug it in again.
There’s no sound or it’s very quiet
Make sure the speaker set A or B is on ( page 19).
Make sure that all audio connecting plugs are pushed
in all the way ( page 14-17).
Make sure that the polarity of the speaker cables is
correct, and that the bare wire is in contact with the
metal part of each speaker terminal (
page 10).
Make sure that the speaker cables are not shorting.
Make sure that the inputs and outputs of all
components are connected properly.
Make sure that the correct input source is selected
(
page 19).
If the MUTING indicator is shown on the display,
press the remote controller’s [MUTING] button to
unmute the receiver (
page 19).
If your turntable uses an MC cartridge, you must
connect an MC head amp, or an MC transformer and
a phono preamp.
Make sure that the digital input source is selected
properly (
page 41).
The receiver does not support multichannel audio
input. The PCM signal can be input only to digital
input terminals. Make sure that PCM is selected on the
playback component (
page 14, 41).
While a pair of headphones is connected to the
PHONES jack, no sound is output from the speakers.
(
page 19)
Noise can be heard
Using cable ties to bundle audio cables with power
cords, speaker cables, and so on may degrade the
audio performance; do not bundle audio cables
together with power cords or speaker cables.
An audio cable may be picking up interference. Try
repositioning your cables.
The tone controls have no effect
If the DIRECT is turned on, or PURE AUDIO button
lights up, the tone controls have no effect. Press the
[AUDIO] or [PURE AUDIO] button to turn the
function off. The PURE AUDIO buttons indicator
will go off (
page 20).
There’s no picture
Make sure that all video connecting plugs are pushed
in all the way. (
page 14)
Make sure that each video component is properly
connected. (
page 14, 16)
If the video source is connected to a composite video
input, your TV must be connected to the
corresponding composite video output. (
page 14)
Reception is noisy, stereo FM reception suffers
from hiss, or the FM STEREO indicator doesn’t
appear
Relocate your antenna.
Move the receiver away from your TV or computer.
Listen to the station in mono ( page 23).
When listening to an AM station, operating the remote
controller may cause noise.
Passing cars and airplanes can cause interference.
Concrete walls weaken radio signals.
If nothing improves the reception, install an outdoor
antenna.
The remote controller doesn’t work
After inserting or replacing the batteries, press the
remote controller’s [MAIN] or [Zone 2] button before
you start performing the desired operation (
page 9).
Make sure that the batteries are installed with the
correct polarity (
page 6).
Install new batteries. Don’t mix different types of
batteries or old and new batteries ( page 6).
Make sure that the remote controller is not too far
away from the receiver, and that there’s no obstruction
between the remote controller and the receiver’s
remote control sensor (
page 6).
Make sure that the receiver is not subjected to direct
sunshine or inverter-type florescent lights. Relocate if
necessary (
page 6).
Power
Audio
If you can’t resolve the issue yourself, try resetting
the receiver before contacting your Onkyo dealer.
To reset the receiver to its factory defaults, turn
it on and, while holding down the [TUNING
MODE] button, press the [ON/STANDBY]
button.
Note that resetting the receiver will delete your
radio presets and custom settings.
Video
Tuner
Remote Controller
51


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-8050 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-8050 in the language / languages: English as an attachment in your email.

The manual is 6,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-8050

Onkyo TX-8050 User Manual - German - 112 pages

Onkyo TX-8050 User Manual - Dutch - 112 pages

Onkyo TX-8050 User Manual - French - 112 pages

Onkyo TX-8050 User Manual - Italian - 112 pages

Onkyo TX-8050 User Manual - Swedish - 112 pages

Onkyo TX-8050 User Manual - Spanish - 112 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info