549886
32
Zoom out
Zoom in
Previous page
1/36
Next page
En-32
Troubleshooting
If you have any trouble using the receiver, look for a
solution in this section.
Can’t turn on the receiver
Make sure that the power cord is plugged into the
electric outlet properly.
Unplug the power cord from the electric outlet, wait
5 seconds or more, then plug it in again.
There’s no sound or it’s very quiet
Make sure the speaker set A or B is on (
page 20).
Make sure that all audio connecting plugs are pushed
in all the way (
page 15-18).
Make sure that the polarity of the speaker cables is
correct, and that the bare wire is in contact with the
metal part of each speaker terminal (
page 11).
Make sure that the speaker cables are not shorting.
Make sure that the inputs and outputs of all
components are connected properly.
Make sure that the correct input source is selected
(
page 20).
If the MUTING indicator is shown on the display,
press the remote controller’s [MUTING] button to
unmute the receiver ( page 20).
If your turntable uses an MC cartridge, you must
connect an MC head amp, or an MC transformer and
a phono preamp.
While a pair of headphones is connected to the
PHONES jack, no sound is output from the speakers.
( page 20).
Noise can be heard
Using cable ties to bundle audio cables with power
cords, speaker cables, and so on may degrade the
audio performance; do not bundle audio cables
together with power cords or speaker cables.
An audio cable may be picking up interference. Try
repositioning your cables.
The tone controls have no effect
If the DIRECT is turned on, the tone controls have no
effect. Press the [TONE] button to turn the function
off.
Reception is noisy, stereo FM reception suffers
from hiss, or the FM STEREO indicator doesn’t
appear
Relocate your antenna.
Move the receiver away from your TV or computer.
Listen to the station in mono (
page 24).
When listening to an AM station, operating the remote
controller may cause noise.
Passing cars and airplanes can cause interference.
Concrete walls weaken radio signals.
If nothing improves the reception, install an outdoor
antenna.
The remote controller doesn’t work
Make sure that the batteries are installed with the
correct polarity (
page 6).
Install new batteries. Don’t mix different types of
batteries or old and new batteries (
page 6).
Make sure that the remote controller is not too far
away from the receiver, and that there’s no obstruction
between the remote controller and the receiver’s
remote control sensor ( page 6).
Make sure that the receiver is not subjected to direct
sunshine or inverter-type florescent lights. Relocate if
necessary ( page 6).
Can’t control other components
If it is an Onkyo component, make sure that the

cable and analog audio cable are connected properly.
Connecting only an
cable won’t work (
page 17).
With some components, certain buttons may not work
as expected, and some may not work at all.
To control an Onkyo component that’s connected via
, point the remote controller at the receiver.
Power
Audio
If you can’t resolve the issue yourself, try resetting
the receiver before contacting your Onkyo dealer.
To reset the receiver to its factory defaults, turn
it on and, while holding down the [TUNING
MODE] button, press the [ON/STANDBY]
button.
Note that resetting the receiver will delete your
radio presets and custom settings.
Tuner
Remote Controller
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-8020 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-8020 in the language / languages: English as an attachment in your email.

The manual is 5,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-8020

Onkyo TX-8020 User Manual - German, Dutch - 132 pages

Onkyo TX-8020 User Manual - French - 68 pages

Onkyo TX-8020 User Manual - Italian, Swedish - 132 pages

Onkyo TX-8020 User Manual - Spanish - 68 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info