549886
11
Zoom out
Zoom in
Previous page
1/36
Next page
En-11
Connecting the Receiver
Disconnect the power cord from the electrical outlet before making any connections.
The receiver allows you to connect two sets of speakers.
When two sets of speakers are connected, you can select
which speaker set outputs sound or use both sets to
output sound simultaneously. ( page 20 about
“Speakers A” and “Speakers B”)
When you connect one set of speakers to either
SPEAKERS A or SPEAKERS B terminal posts, or
when you connect two sets of speakers to both speaker
terminal posts and output sound only from either
speaker set, use speakers whose impedance is 4 to
16 Ω, and set the speaker impedance setting on the
receiver to 4 or 6 Ω ( page 13). When the impedance
of the speaker to be used is less than 6 Ω, set the
speaker impedance to 4 Ω.
When you connect speakers to both SPEAKERS A
and SPEAKERS B terminal posts and output sound
from both speaker sets simultaneously, use speakers
whose impedance is 8 to 16 Ω. Set the speaker
impedance setting on the receiver to 4 Ω.
Read the instructions supplied with your speakers.
Pay close attention to speaker wiring polarity. In other
words, connect positive (+) terminals only to positive (+)
terminals, and negative (–) terminals only to negative (–)
terminals. If you get them the wrong way around, the
sound will be out of phase and will sound unnatural.
Unnecessarily long or very thin speaker cables may
affect the sound quality and should be avoided.
Be careful not to short the positive and negative wires.
Doing so may damage the receiver.
Don’t connect more than one cable to each speaker
terminal. Doing so may damage the receiver.
Don’t connect a speaker to more than one pair of
speaker terminals.
Note:
If you make an incorrect setting for the speakers or the
impedance values, the built-in protection circuit may be
activated resulting in no sound output from speakers.
1
Strip about 5/8" (15 mm)
of insulation from the
ends of the speaker
cables, and twist the
bare wires tightly, as
shown.
2
Unscrew the terminal.
3
Fully insert the bare wire.
4
Screw the terminal tight.
The following illustration shows which speaker should
be connected to each pair of terminals.
Speaker Connection Precautions Connecting the Speaker Cables
5/8" (15 mm)
++ ++
Receiver
Right
speaker
Left
speaker
Speaker set BSpeaker set A
Right
speaker
Left
speaker
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-8020 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-8020 in the language / languages: English as an attachment in your email.

The manual is 5,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-8020

Onkyo TX-8020 User Manual - German, Dutch - 132 pages

Onkyo TX-8020 User Manual - French - 68 pages

Onkyo TX-8020 User Manual - Italian, Swedish - 132 pages

Onkyo TX-8020 User Manual - Spanish - 68 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info