161038
16
Zoom out
Zoom in
Previous page
1/28
Next page
E
n
AM/FM Tuner
T-4555
(European model)
DAB/AM/FM Tuner
T-4555
(U.K. model)
Instruction Manual
Thank you for purchasing an Onkyo Tuner. Please
read this manual thoroughly before making connec-
tions and plugging in the unit.
Following the instructions in this manual will enable
you to obtain optimum performance and listening
enjoyment from your new Tuner.
Please retain this manual for future reference.
Contents
Introduction.................................... 2
Connections ................................. 10
Enjoying Audio Sources.............. 15
Troubleshooting........................... 26
Specifications .............................. 27
2
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radia-
tors, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are pro-
vided for your safety. If the provided plug does not
fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience recepta-
cles, and the point where they exit from the appara-
tus.
11. Only use attachments/accessories specified by the
manufacturer.
12.
Use only with the cart, stand,
tripod, bracket, or table spec-
ified by the manufacturer, or
sold with the apparatus.
When a cart is used, use cau-
tion when moving the cart/
apparatus combination to
avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or
when unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
15. Damage Requiring Service
Unplug the apparatus from the wall outlet and refer
servicing to qualified service personnel under the
following conditions:
A. When the power-supply cord or plug is damaged,
B. If liquid has been spilled, or objects have fallen
into the apparatus,
C. If the apparatus has been exposed to rain or
water,
D. If the apparatus does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions as an improper adjustment of other
controls may result in damage and will often
require extensive work by a qualified technician
to restore the apparatus to its normal operation,
E. If the apparatus has been dropped or damaged in
any way, and
F. When the apparatus exhibits a distinct change in
performance this indicates a need for service.
16. Object and Liquid Entry
Never push objects of any kind into the apparatus
through openings as they may touch dangerous volt-
age points or short-out parts that could result in a
fire or electric shock.
The apparatus shall not be exposed to dripping or
splashing and no objects filled with liquids, such as
vases shall be placed on the apparatus.
Don’t put candles or other burning objects on top of
this unit.
17. Batteries
Always consider the environmental issues and fol-
low local regulations when disposing of batteries.
18. If you install the apparatus in a built-in installation,
such as a bookcase or rack, ensure that there is ade-
quate ventilation.
Leave 20 cm (8") of free space at the top and sides
and 10 cm (4") at the rear. The rear edge of the shelf
or board above the apparatus shall be set 10 cm (4")
away from the rear panel or wall, creating a flue-like
gap for warm air to escape.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPARATUS
TO RAIN OR MOISTURE.
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK). NO
USER-SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
RISQUE DE CHOC ELECTRIQUE
NE PAS
OUVRIR
AVIS
PORTABLE CART WARNING
S3125A
3
Precautions
1. Recording Copyright
—Unless it’s for personal use
only, recording copyrighted material is illegal with-
out the permission of the copyright holder.
2. AC Fuse
—The AC fuse inside the unit is not user-
serviceable. If you cannot turn on the unit, contact
your Onkyo dealer.
3. Care
—Occasionally you should dust the unit all
over with a soft cloth. For stubborn stains, use a soft
cloth dampened with a weak solution of mild deter-
gent and water. Dry the unit immediately afterwards
with a clean cloth. Don’t use abrasive cloths, thin-
ners, alcohol, or other chemical solvents, because
they may damage the finish or remove the panel let-
tering.
4. Power
WARNING
BEFORE PLUGGING IN THE UNIT FOR THE
FIRST TIME, READ THE FOLLOWING SEC-
TION CAREFULLY.
AC outlet voltages vary from country to country.
Make sure that the voltage in your area meets the
voltage requirements printed on the unit’s rear panel
(e.g., AC 230 V, 50 Hz or AC 120 V, 60 Hz).
The power cord plug is used to disconnect this unit
from the AC power source. Make sure that the plug
is readily operable (easily accessible) at all times.
For American Models
Pressing the [STANDBY/ON] button to select
Standby mode does not fully shutdown the unit. If
you do not intend to use the unit for an extended
period, remove the power cord from the AC outlet.
5. Never Touch this Unit with Wet Hands
—Never
handle this unit or its power cord while your hands
are wet or damp. If water or any other liquid gets
inside this unit, have it checked by your Onkyo
dealer.
6. Handling Notes
If you need to transport this unit, use the original
packaging to pack it how it was when you origi-
nally bought it.
Do not leave rubber or plastic items on this unit
for a long time, because they may leave marks on
the case.
This unit’s top and rear panels may get warm
after prolonged use. This is normal.
If you do not use this unit for a long time, it may
not work properly the next time you turn it on, so
be sure to use it occasionally.
For British models
Replacement and mounting of an AC plug on the power
supply cord of this unit should be performed only by
qualified service personnel.
IMPORTANT
The wires in the mains lead are coloured in accordance
with the following code:
Blue: Neutral
Brown: Live
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured mark-
ings identifying the terminals in your plug, proceed as
follows:
The wire which is coloured blue must be connected to
the terminal which is marked with the letter N or
coloured black.
The wire which is coloured brown must be connected to
the terminal which is marked with the letter L or
coloured red.
IMPORTANT
The plug is fitted with an appropriate fuse. If the fuse
needs to be replaced, the replacement fuse must
approved by ASTA or BSI to BS1362 and have the same
ampere rating as that indicated on the plug. Check for
the ASTA mark or the BSI mark on the body of the fuse.
If the power cord’s plug is not suitable for your socket
outlets, cut it off and fit a suitable plug. Fit a suitable
fuse in the plug.
For European Models
Memory backup
The T-4555 uses a battery-less memory backup system
in order to retain radio presets and other settings when
it’s unplugged or in the case of a power failure.
Although no batteries are required, the T-4555 must be
plugged into an AC outlet in order to charge the backup
system.
Once it has been charged, the T-4555 will retain the set-
tings for several weeks, although this depends on the
environment and will be shorter in humid climates.
Declaration of Conformity
We,
ONKYO EUROPE
ELECTRONICS GmbH
LIEGNITZERSTRASSE 6,
82194 GROEBENZELL,
GERMANY
GROEBENZELL, GERMANY
ONKYO EUROPE ELECTRONICS GmbH
K. MIYAGI
declare in own responsibility, that the ONKYO product
described in this instruction manual is in compliance with the
corresponding technical standards such as EN60065,
EN55013, EN55020 and EN61000-3-2, -3-3.
4
Features
Tuner board upgrade capability
12V trigger IN/OUT
RS232 port
IR IN/OUT
Hi-rigidity, anti-resonant chassis
Aluminium front panel
RI (Remote Interactive) capable
European Model
Automatic AM/FM tuning
40 AM/FM presets
RDS (Radio Data System)
Preset auto scan
Direct tuning
U.K. Model
Automatic AM/FM/DAB tuning
40 AM/FM/DAB presets
RDS (Radio Data System)
DAB auto scanning (Band III/L-Band)
Preset auto scan
Direct tuning
Ground isolation circuit for digital/analog
Supplied Accessories
Make sure you have the following accessories:
Remote controller and two batteries (AA/R6)
Audio cable (60 cm)
cable (60 cm)
To use , the T-4555 must be connected with an
cable and an audio cable.
Indoor FM antenna
AM loop antenna
DAB antenna (with U.K. model)
* In catalogs and on packaging, the letter added to the end of
the product name indicates the color of the T-4555. Specifi-
cations and operation are the same regardless of color.
5
Contents
Important Safety Instructions.....................................................................................2
Precautions..................................................................................................................3
Features .......................................................................................................................4
Supplied Accessories .................................................................................................4
Getting to Know the T-4555........................................................................................6
Front Panel ............................................................................................................6
Display...................................................................................................................6
Rear Panel.............................................................................................................7
Remote Controller .......................................................................................................8
Remote Controller .................................................................................................8
Before Using the T-4555 .............................................................................................9
Installing the Batteries ...........................................................................................9
Aiming the Remote Controller ...............................................................................9
Introduction
Connecting Antennas ...............................................................................................10
Connecting the Indoor FM Antenna.....................................................................10
Connecting the AM Loop Antenna.......................................................................10
Connecting the T-4555..............................................................................................12
Connecting to an Amplifier ..................................................................................12
About the System Functions................................................................................12
Connecting the 12V Trigger Jacks ......................................................................13
Controlling Components That Are Out of Range.................................................14
Connections
Turning On and Listening to AM and FM Radio .....................................................15
Turning On the T-4555 ........................................................................................15
Setting the Display Brightness.............................................................................15
Listening to AM and FM Radio ............................................................................15
Tuning into Stations by Frequency ......................................................................16
Using RDS...........................................................................................................17
Listening to DAB Digital Radio ................................................................................19
DAB Setup...........................................................................................................20
Using Presets ............................................................................................................22
Presetting Your Favorite Stations........................................................................22
Selecting Presets.................................................................................................22
Deleting Presets ..................................................................................................22
Changing the Remote ID...........................................................................................23
Optional Tuner Boards..............................................................................................24
AM Frequency Step Setup ..................................................................................24
Installing a Board.................................................................................................25
Enjoying Audio Sources
Troubleshooting ........................................................................................................26
Specifications ............................................................................................................27
If you can’t resolve an issue, try resetting the AV receiver by holding down the [MEMORY] but-
ton and pressing the [STANDBY/ON] button.
Others
6
Getting to Know the T-4555
For detailed information, refer to the pages in parentheses.
A
STANDBY/ON button (15)
Sets the T-4555 to On or Standby.
B
STANDBY indicator (15)
Lights up when the T-4555 is on Standby.
C
CATEGORY [ ]/[ ] buttons
Selects categories for satellite radio.
As of August 2006, these buttons are not used on the
European or U.K. T-4555.
D
PRESET [ ]/[ ] buttons (18, 22)
Used to select radio presets.
E
RT/PTY/TP button (18)
Used with RDS (Radio Data System).
F
DISPLAY button (20)
Used to view various information on the display.
G
BAND button (15, 18, 19)
Selects AM, FM, or DAB*.
*DAB requires C-DAB tuner board.
H
TUNING/CH [ ]/[ ] buttons (15, 19)
With AM and FM, these buttons are used for tuning.
With DAB, they’re used to select stations.
I
AUTO SCAN button (18, 19, 22)
Selects and outputs each radio preset in turn for 5
seconds. When tuned to an RDS FM station, it
searches for stations by PTY (Program Type) or TP
(Traffic Program). Also used to scan for available
DAB stations.
J
Remote control sensor (9)
Receives control signals from the remote controller.
K
Display
See below.
L
MEMORY button (22)
Used to store and delete radio presets.
M
TUNING MODE button (15, 22)
Selects the Auto or Manual tuning mode for AM
and FM radio.
A
DAB (requires C-DAB tuner board)
Lights up if the installed tuner board supports DAB.
When DAB is selected, a box appears around it.
B
FM
Lights up if the installed tuner board supports FM.
When FM is selected, a box appears around it.
C
AM
Lights up if the installed tuner board supports AM.
When AM is selected, a box appears around it.
D RDS
Lights up when the tuner is tuned to an FM radio
station that supports RDS (Radio Data System).
E STEREO
Lights up when radio reception is in stereo.
F MONO
Lights up when radio reception is in mono.
G SECONDARY
Lights up when tuned to an DAB station that’s
transmitting secondary multicast channels.
H TUNED
The TUNED indicator lights up when properly
tuned to a radio station. During Auto Tuning, the
Tuning Arrows flash.
I AUTO
Lights up when Auto Tuning mode is selected.
J MEMORY
Lights up when presetting radio stations.
K Message area
Various information is displayed here, including
radio preset numbers, tuning frequency, and so on.
Front Panel
A
9KJLM
BC45 67 8
Display
123456879J
K
7
Getting to Know the T-4555—Continued
European Model
Comes with C-AMFM tuner board installed.
U.K. Model
Comes with C-DAB tuner board installed.
For detailed information, refer to the pages in parentheses.
A DAB ANTENNA (C-DAB tuner board only)
(11)
This jack is for connecting the supplied DAB
antenna.
B AM ANTENNA (10)
These push terminals are for connecting the sup-
plied AM loop antenna or an outdoor AM antenna.
C FM 75 ANTENNA (10)
This jack is for connecting the supplied indoor FM
antenna or an outdoor FM antenna.
D AUDIO OUTPUT (12)
Using the supplied audio cable, connect these out-
put jacks to an analog audio input on your amp.
E REMOTE CONTROL (13)
These two identical (Remote Interactive) jacks
can be connected to the jacks on your other
Onkyo components for interactive control. To use
, the T-4555 must be connected with an
cable and an audio cable.
F 12V TRIGGER IN/OUT (13)
The 12V TRIGGER IN jack can be connected to the
12-volt trigger output on another component, so that
when the other component is turned on, the T-4555
turns on as well.
The 12V TRIGGER OUT jack can be connected to
the 12-volt trigger input on another component, so
that when the T-4555 is turned on, the other compo-
nent turns on as well.
G IR IN/OUT (14)
A commercially available IR receiver can be con-
nected to the IR IN jack, allowing you to control the
T-4555 while you’re in another room, or control it
when it’s out of sight, for example, installed in a
cabinet.
A commercially available IR emitter can be con-
nected to the IR OUT jack to pass IR (infrared)
remote control signals through to other components.
H RS232
This port is for connecting the T-4555 to home
automation equipment and external controllers.
I Power cord (15)
The power cord should be connected to a suitable
wall outlet.
Rear Panel
32 4567 8 9
9
1234
5
67 8
See pages 10–14 for connection information.
8
Remote Controller
A STANDBY/ON button (15)
Sets the T-4555 to On or Standby.
B Number buttons (16, 23)
Used to select radio presets by number, and to enter
AM/FM station frequencies and DAB channel num-
bers in Direct Tuning mode.
C DIRECT TUNING button (16)
Selects the Direct Tuning mode. With AM and FM,
you can select a station directly by entering its fre-
quency. Direct Tuning mode does not work with
DAB.
D RETURN button (23)
Returns to the previous display.
E Arrow [ ]/[ ]/[ ]/[ ] buttons (20, 21, 23, 24)
With AM and FM, the Up and Down [ ]/[ ] but-
tons are used for tuning. With DAB, the Up and
Down [ ]/[ ] buttons are used to select stations.
The Left and Right [ ]/[ ] buttons are not used by
the C-AMFM and C-DAB tuner boards.
F PRESET [+]/[–] buttons (22)
Used to select radio presets.
G AUTO SCAN button (19, 22)
Scans for DAB stations or FM stations that support
RDS.
H BAND button (15, 19)
Selects AM, FM, or DAB*.
I DISPLAY button (20)
Used to change the information shown on the dis-
play.
J DIMMER button (15)
Adjusts the display brightness.
K ENT and ENTER buttons (20, 21, 23, 24)
Used to confirm various functions and settings.
L SETUP button (20, 23, 24)
Selects Setup mode.
M TUNING/CH [ ]/[ ] buttons (15, 19)
With AM and FM, these buttons are used for tuning.
With DAB, they’re used to select stations.
N TUNING MODE button (15)
Selects the Auto or Manual Tuning mode for AM
and FM radio.
*DAB requires C-DAB tuner board.
Remote Controller
1
2
3
4
9
J
L
6
7
8
5
K
M
N
9
Before Using the T-4555
Notes:
If the remote controller doesn’t work reliably, try
replacing the batteries.
Don’t mix new and old batteries or different types of
batteries.
If you intend not to use the remote controller for a
long time, remove the batteries to prevent damage
from leakage and corrosion.
Flat batteries should be removed as soon as possible
to prevent damage from leakage and corrosion.
When using the remote controller, point it toward the
T-4555’s remote control sensor, as shown below.
Notes:
The remote controller may not work reliably if the
T-4555 is subjected to bright light, such as direct sun-
light or inverter-type fluorescent lights. Keep this in
mind when installing.
If another remote controller of the same type is used
in the same room, or the T-4555 is installed close to
equipment that uses infrared rays, the remote control-
ler may not work reliably.
Don’t put anything, such as a book, on the remote
controller because the buttons may be pressed inad-
vertently, thereby draining the batteries.
The remote controller may not work reliably if the
T-4555 is installed in a rack behind colored glass
doors. Keep this in mind when installing.
The remote controller will not work if there’s an
obstacle between it and the T-4555’s remote control
sensor.
Installing the Batteries
1
Open the battery compartment, as shown.
2
Insert the two supplied batteries (AA) in
accordance with the polarity diagram
inside the battery compartment.
3
Close the battery compartment.
Aiming the Remote Controller
30˚
30˚
T-4555
Remote control sensor
Approx.
5 m
10
Connecting Antennas
This section explains how to connect the supplied
indoor FM antenna, AM loop antenna, and DAB
antenna, and how to connect commercially available
outdoor FM and AM antennas.
European model
U.K. model
The supplied indoor FM antenna is for indoor use only.
If you cannot achieve good reception with the supplied
indoor FM antenna, try using a commercially available
outdoor FM antenna instead.
The supplied indoor AM loop antenna is for indoor use
only.
If you cannot achieve good reception with the supplied
indoor AM loop antenna, try using it with a commer-
cially available outdoor AM antenna.
Connecting the Indoor FM Antenna
1
Attach the FM antenna, as shown.
Once the T-4555 is ready for use, you’ll need to
tune into an FM radio station and adjust the posi-
tion of the FM antenna to achieve the best possi-
ble reception.
2
Use thumbtacks or something similar to
fix the FM antenna into position.
Caution: Be careful that you don’t injure your-
self when using thumbtacks.
AM antenna push terminals
FM antenna jack
AM antenna push terminals
FM antenna jack
Insert the plug fully
into the jack.
Thumbtacks, etc.
Connecting the AM Loop Antenna
1
Assemble the AM loop antenna, inserting
the tabs into the base, as shown.
2
Connect both wires of the AM loop
antenna to the AM push terminals, as
shown.
(The antenna’s wires are not polarity sensitive, so
they can be connected either way around).
Make sure that the wires are attached securely and
that the push terminals are gripping the bare
wires, not the insulation.
Once the T-4555 is ready for use, you’ll need to
tune into an AM radio station and adjust the posi-
tion of the AM antenna to achieve the best possi-
ble reception.
Keep the antenna as far away as possible from the
T-4555, TV, speaker cables, and power cords.
Push Insert wire Release
11
Connecting Antennas—Continued
Connecting the DAB Antenna
(C-DAB Tuner Board Only)
Connecting an Outdoor FM Antenna
If you cannot achieve good reception with the supplied
indoor FM antenna, try a commercially available out-
door FM antenna instead.
Notes:
Outdoor FM antennas work best outside, but usable
results can sometimes be obtained when installed in
an attic or loft.
•For best results, install the outdoor FM antenna well
away from tall buildings, preferably with a clear line
of sight to your local FM transmitter.
Outdoor antenna should be located away from possi-
ble noise sources, such as neon signs, busy roads, etc.
•For safety reasons, outdoor antenna should be situ-
ated well away from power lines and other high-volt-
age equipment.
Outdoor antenna must be grounded in accordance
with local regulations to prevent electrical shock haz-
ards.
Using a TV/FM Antenna Splitter
It’s best not to use the same antenna for both FM and
TV reception, as this can cause interference problems. If
circumstances demand it, use a TV/FM antenna splitter,
as shown.
Connecting an Outdoor AM Antenna
If good reception cannot be achieved using the supplied
AM loop antenna, an outdoor AM antenna can be used
in addition to the loop antenna, as shown.
Outdoor AM antennas work best when installed hori-
zontally outside, but good results can sometimes be
obtained indoors by mounting horizontally above a win-
dow. Note that the AM loop antenna should be left con-
nected.
Outdoor antenna must be grounded in accordance with
local regulations to prevent electrical shock hazards.
1
Screw the supplied DAB antenna’s plug
onto the DAB ANTENNA jack.
Once the T-4555 is ready for use, you’ll need to
select a DAB station and adjust the position of
the DAB antenna to achieve the best possible
reception.
2
Use thumbtacks or something similar to
fix the DAB antenna into position.
To T-4555 To TV (or VCR)
TV/FM antenna splitter
Outdoor antenna
AM loop antenna
Insulated antenna cable
12
Connecting the T-4555
Use the supplied audio cable to connect the T-4555’s
AUDIO OUTPUT L/R jacks to the TUNER IN jacks on
your amplifier, as shown.
To use the system functions, use the supplied
cable to make an connection (see the next column).
Note:
If the T-4555 is used with another Onkyo component,
such as the A-9555, refer to its instruction manual as
well.
If you connect the T-4555 to another Onkyo -capa-
ble component with the supplied cable and audio
cable, you can use the following system functions.
cables are special cables solely for use with Onkyo
products.
Auto Power On
When you turn on the T-4555, your Onkyo amplifier
will turn on automatically. (The amplifier’s POWER
switch must be set to ON for this to work.)
Direct Change
When you select a radio preset or change the band (AM,
FM, DAB), your Onkyo amplifier will automatically
select the T-4555 as the input source.
Remote Control Operation
You can control the T-4555 by using your Onkyo ampli-
fier’s remote controller. See the amplifier’s instruction
manual for details.
Before Making Any Connections
Refer to the instructions that came with the com-
ponent you are connecting.
Do not plug in the power cord until all other con-
nections are complete.
Do not bind audio cables with power cords and
speaker cables. Doing so may adversely affect the
sound quality.
•To prevent interference, keep power cords and
speaker cables as far away as possible from the
antennas.
RCA Audio Connection Color Coding
Red plugs are used for the right channel, white
plugs are used for the left channel.
Push each plug in all the way to make a good con-
nection (loose connections can cause noise or mal-
functions).
Left (white)
Right (red)
L
R
Wrong!
Right!
Connecting to an Amplifier
T-4555
L
R
TUNER
Amplifier
Supplied cable
Supplied audio
cable
About the System Functions
13
Connecting the T-4555—Continued
With (Remote Interactive), you can control your
-capable Onkyo CD player, T-4555, and so on with
your amp’s remote controller.
•To use , you must make an analog audio con-
nection between your amplifier and each audio
component.
Notes:
Push each plug in all the way to make a good connec-
tion.
Use only dedicated cables for connections.
cables are supplied with Onkyo tuners and play-
ers (DVD, CD, etc.).
Some components, including the T-4555, have two
jacks. They’re both the same, so use either one.
jacks should be connected only to Onkyo compo-
nents. Connecting them to another manufacturer’s
component may cause a malfunction.
Some components may not support all functions.
See the manuals supplied with your other Onkyo
components for more information.
To have the T-4555 turn on automatically when another
component is turned on, connect the T-4555’s 12V
TRIGGER IN jack to a 12-volt trigger output on the
other component with a miniplug cable.
Likewise, to have another component turn on automati-
cally when the T-4555 is turned on, connect the
T-4555’s 12V TRIGGER OUT jack to a 12-volt trigger
input on the other component with a miniplug cable.
Onkyo amplifier
(A-9555), etc.
Onkyo CD player
(DX-7555), etc.
T-4555
Remote Interactive
Dock, etc.
jack
jack
jack
cable
Connecting the 12V Trigger Jacks
STANDBY/ON
ZONE2
ZONE 2 LEVEL
PHONES
MULTl CH
TONE
+
STEREO
LISTENING MODE
DISPLAY
DIGITAL INPUT
RT/PTY/TP
MEMORY
TUNING MODE
RETURN
TUNING / PRESET
ENTER
SETUP
DVD VIDEO 1 VIDEO 2
VCR 1 VCR 2
VIDEO 3 VIDEO 4 TAPE TUNER CD
SETUP MIC S VIDEO VIDEO
MASTER VOLUME
VIDEO 4 INPUT
LR
AUDIO
DIGITAL
OFF
STANDBY
CLEAR
PURE AUDIO
12 V
TRIGGER
OUT
ZONE 2
IN
12
V
TRIGGER
Amplifier, AV receiver, etc.
T-4555
CD player, etc.
14
Connecting the T-4555—Continued
You can use the following multi-room kits to control the
T-4555 when it’s out of range of the remote controller:
Multiroom AV distribution and control systems such
as those made by Niles
®
and Xantech
®
.
Controlling the T-4555 When It’s Out of
Range
If the T-4555 is located in another room, installed in a
cabinet, or out of range of its remote controller, you can
use a commercially available IR receiver to pickup the
remote controller signals and feed them to the T-4555,
as shown below.
Connect the IR receiver to the T-4555 as shown below.
Controlling Other Out-of-range
Components
If another component is out of range of its remote con-
troller, you can use a commercially available IR emitter
to retransmit the remote controller signals received at
the T-4555’s IR IN, as shown below.
Connect the IR emitter to the T-4555’s IR OUT, and
place the IR emitter in front of the other component’s
remote control sensor (usually located on its front
panel), as shown below. See the instructions supplied
with the IR emitter.
Only remote controller signals received by the T-4555’s
IR IN are fed through to the IR OUT. Signals picked up
by the T-4555’s remote control sensor are not output.
Controlling Components That Are Out of Range
IR IN
T-4555
Connecting
block
IR Receiver
Inside
cabinet
Remote controller
Signal flow
T-4555
Miniplug cable
From the connecting block
IR IN
IR OUT
T-4555
Connecting
block
IR Receiver
Remote controller
Signal flow
IR Emitter
Other component
T-4555
Signal flow
Other component
IR Emitter
Miniplug
Miniplug cable
IR Emitter
Remote
control
sensor
From the
connecting block
15
Turning On and Listening to AM and FM Radio
With this function, you can adjust the brightness of the
display.
Tuning into weak stereo FM stations
If the signal from a stereo FM station is weak, it may be
impossible to get good reception. In this case, switch to
Manual Tuning mode and listen to the station in mono.
Turning On the T-4555
1
Connect the power cord to a suit-
able wall outlet.
2
Press the [STANDBY/ON] button
on the T-4555 or remote control-
ler.
The T-4555 turns on, and the
STANDBY indicator goes off.
To turn off the T-4555, press the
[STANDBY/ON] button. The T-4555
will enter Standby mode.
Note that the T-4555 is not completely
shutdown in Standby mode.
Setting the Display Brightness
Press the remote controller’s
[DIMMER] button repeatedly to
select: dim, dimmer, or normal
brightness.
STANDBY/ON
STANDBY/ON
TUNING/CH
BAND
TUNING MODE
TUNING/CH
TUNING MODE
DIMMER
BAND
/
STANDBY indicator
Remote controller
Remote controller
Listening to AM and FM Radio
1
Press the [BAND] button repeat-
edly to select AM or FM.
The or indicator lights up.
2
Press the [TUNING MODE] but-
ton repeatedly to select Auto or
Manual Tuning mode.
•Auto Tuning Mode
The AUTO indicator appears and
stereo radio reception is possible.
Manual Tuning Mode
The MONO indicator appears and
radio reception will be in mono.
3
Use the TUNING/CH [ ]/[ ] but-
tons to tune into a station.
In Auto Tuning mode, once a station is
found, tuning stops automatically.
This model changes FM frequency in
0.05 MHz steps, 9 kHz steps for AM.
In Manual Tuning mode, the frequency
stops changing when you release the
buttons. Press the buttons repeatedly to
change the frequency one step at a
time.
When tuned into a station, the
TUNED indicator appears.
Remote controller
Remote controller
AUTO indicator
MONO indicator
Remote controller
TUNED
16
Turning On and Listening to AM and FM Radio—Continued
You can tune into AM and FM stations directly by
entering the appropriate frequency.
Adjusting the Antennas
Tuning into Stations by Frequency
1
Press the [DIRECT TUNING] but-
ton.
(Actual display depends on country.)
2
Within 8 seconds, use the num-
ber buttons to enter the fre-
quency of the radio station.
For example, to tune into an FM sta-
tion at 87.5 MHz, press [8], [7], and
[5].
Number buttons
DIRECT TUNING
Remote controller
Remote controller
2
1
Change the direction of the
antenna to achieve the best
possible reception.
Affix the antenna with a thumbtack. (Do not
push the thumbtack through the antenna.)
Caution: Be careful not to prick your finger!
Adjusting the AM antenna
Adjust the location and position of the
AM antenna while listening to an AM sta-
tion to achieve the best possible reception.
Adjusting and installing the FM antenna
Choose a location for the FM antenna while
listening to an FM station.
17
Turning On and Listening to AM and FM Radio—Continued
RDS only works with European and U.K. models and
only in areas where RDS broadcasts are available.
What is RDS?
RDS stands for Radio Data System and it’s a method of
transmitting data in FM radio signals. It was developed
by the European Broadcasting Union (EBU) and is
available in most European countries. Many FM sta-
tions use it these days. In addition to displaying text
information, RDS can also help you find radio stations
by type (e.g., news, sport, rock, etc.).
The T-4555 supports the following types of RDS data:
PS (Program Service)
When tuned to an RDS station that’s broadcasting PS
information, the station’s name will be displayed. Press-
ing the [DISPLAY] button will display the current fre-
quency for 3 seconds.
RT (Radio Text)
When tuned to an RDS station that’s broadcasting RT
text information, the text will be shown on the display
(see page 18).
PTY (Program Type)
With PTY, you can search for radio stations by type (see
page 18).
TP (Traffic Program)
With TP, you can listen to traffic information (see
page 18).
Notes:
In some cases, the text characters displayed on the AV
receiver may not be identical to those broadcast by
the radio station. Also, unexpected characters may be
displayed when unsupported characters are received.
This is not a malfunction.
If the signal from an RDS station is weak, RDS data
may be displayed intermittently or not at all.
Program Types Used in Europe (PTY)
Using RDS
Type Display Description
None NONE No program type.
News
reports
NEWS Reports on current events and
happenings.
Current
affairs
AFFAIRS Topical reporting of current
affairs, often with a wider
range of topics than news
reports.
Information INFO General information such as
weather forecasts, consumer
affairs, medical help, etc.
Sport SPORT Live sports action, sports
news, and interviews.
Education EDUCATE Formal educational programs.
Drama DRAMA Radio plays and serials.
Culture CULTURE Cultural programs (including
religious affairs).
Science
and
technology
SCIENCE Programs about the natural
sciences and technology.
Varied VARIED Speech-based programs not
covered by the above
categories (e.g., quizzes,
panel games, and comedy).
Pop music POP M Popular commercial music,
usually from past or present
sales charts (e.g., Top 40).
Rock music ROCK M Popular music with an
alternative appeal, often not
appearing on sales charts.
Middle of
the road
music
M.O.R.M Easy listening music (as
opposed to Pop, Rock, or
Classical).
Light
classics
LIGHT M Classical music for general
rather than specialist
appreciation.
Serious
classics
CLASSICS Performances of major
orchestral works, symphonies,
chamber music, etc. (including
the Grand Opera).
Other music OTHER M Music styles not covered by
the above categories (e.g.,
Jazz, Rhythm & Blues, Folk,
Country, and Reggae).
Alarm ALARM When an RDS station is
making an emergency
broadcast, ALARM will flash
on the display.
18
Turning On and Listening to AM and FM Radio—Continued
Displaying Radio Text (RT)
When tuned to an RDS station that’s broadcasting RT
text information, you can display information.
Notes:
While the T-4555 waits for RT information, “Wait-
ing” appears on the display.
If “No Text Data” appears on the display, no RT text
information is available.
Finding Stations by Type (PTY)
You can search for radio stations by type.
Listening to Traffic Information (TP)
You can listen to traffic information and search for TP
radio stations.
Press the [RT/PTY/TP] button
once.
The RT information scrolls across the
display.
1
Use the [BAND] button to select
FM.
2
Press the [RT/PTY/TP] button
twice.
The current program type appears on
the display.
3
Use the PRESET [ ]/[ ] buttons
to select the type of program you
want.
See the list of program types on
page 17.
4
To start the search, press [AUTO
SCAN].
The T-4555 searches until it finds a
station of the type you specified, at
which point it stops briefly before con-
tinuing with the search.
BANDRT/PTY/TP
AUTO SCAN
PRESET
/
5
When the station you want to lis-
ten to is found, press [AUTO
SCAN].
If no stations are found, “Not Found”
appears on the display.
1
Use the [BAND] button to select
FM.
2
Press the [RT/PTY/TP] button
three times.
If the current radio station is broadcast-
ing TP (Traffic Program), “[TP]” will
appear on the display and traffic infor-
mation will be heard as and when it’s
broadcast. If “TP” without square
brackets appears, it means that the sta-
tion is not broadcasting TP.
3
To locate a station that is broad-
casting TP, press [AUTO SCAN].
The T-4555 searches until it finds a
station that’s broadcasting TP.
If no stations are found, “Not Found”
appears on the display.
19
Listening to DAB Digital Radio
Selecting DAB for the Very First Time
The very first time you select DAB, the Auto Tuning
function automatically scans the DAB Band III and
L-Band for the multiplexes (i.e., stations) available in
your area.
Once the scanning process is complete, the first station
that was detected is selected.
Using the Auto Tuning Function Manually
If a new DAB station is introduced, or you move to a
new area, you can run the Auto Tuning function again.
To cancel Auto Tuning, press the [AUTO SCAN] button
again.
Selecting DAB Stations
Press the [BAND] button repeat-
edly to select DAB.
The indicator lights up.
When tuned into a DAB station, the
TUNED indicator appears.
AUTO SCAN
AUTO SCAN BAND
TUNING/CH
TUNING/CH
BAND
/
Remote controller
Station name
Tuned indicatorDAB indicator
To start the Auto Tuning function,
press the [AUTO SCAN] button.
The number of stations found and the
scanning progress are shown on the
display.
Use the TUNING/CH [ ]/[ ] but-
tons to select a DAB station.
If a secondary service is available, a
right angle bracket (>) is displayed.
Press the Right Arrow [ ] button to
listen to the secondary service.
While the secondary service is
selected, a left angle bracket (<) is dis-
played and SECONDARY indicator
lights up. Press the Left Arrow [ ]
button to return to the primary service.
When you select a station that you’ve
selected a lot in the past, the letter F
(short for Favorite) is displayed.
If you select a station that cannot be
received properly, a question mark (?)
is displayed.
Remote controller
Remote controller
“>”
“<”
“SECONDARY”
“F”
“?”
20
Listening to DAB Digital Radio—Continued
Displaying DAB Radio Information
Press the [DISPLAY] button repeatedly to display more
information about the current DAB station.
1. DLS (Dynamic Label Segment)
When tuned to a station that’s broadcasting DLS text
data, the text will scroll across the display.
2. Program Type
Displays the type of program.
3. Bit Rate and Audio Mode
Displays the station’s bit rate and audio mode (ste-
reo, mono, or joint stereo).
4. Signal Quality
Displays the signal quality.
0–59: Poor reception
60–79: Good reception
80–100: Excellent reception
5. Multiplex Name
Displays the name of the current multiplex.
6. Multiplex Number and Frequency
Displays the number and frequency of the current
multiplex.
You can configure DAB digital radio with these settings.
St. List (Station Listing)
With this setting, you can sort the available stations
alphabetically, by multiplex, favorites, or active stations.
Use the Left and Right Arrow [ ]/[ ] buttons to select
the following options, and then press [ENTER].
Alp Odr (Alphabetical Order): Sort stations alpha-
betically. This is the default setting.
Mlt Odr (Multiple Order): Sort stations by multi-
plex.
Fav Odr (Favorite Order): Sort stations by favorites.
The stations you select the most will appear at the
top of the list.
Act Odr (Active Station Order): Sort by active sta-
tions. Receivable stations appear at the top of the
list. stations that cannot be received properly
appear at the bottom of the list.
Trim (Trim Station): Removes stations that cannot
be received properly from the listing.
(Scroll)
DAB Setup
1
Press the [SETUP] button.
2
Use the Up and Down Arrow
[ ]/[ ] buttons to select a set-
ting.
Each item is explained below.
SETUP
///
ENTER
Remote controller
Remote controller
21
Listening to DAB Digital Radio—Continued
Scan Mode
This setting determines which DAB bands are scanned
by the Auto Tuning function (see page 19).
Use the Left and Right Arrow [ ]/[ ] buttons to select
the following options, and then press [ENTER].
UK: Band III (11B–12D).
WorldW (Worldwide): Band III (5A–13F) and
L-Band (LA–LW). This is the default setting.
DRC Value
With the DRC (Dynamic Range Control) setting, you
can reduce the dynamic range of DAB digital radio so
that you can still hear quiet parts even when listening at
low volume levels—ideal for listening to the radio late at
night when you don’t want to disturb anyone.
Use the Left and Right Arrow [ ]/[ ] buttons to select
from the following options, and then press [ENTER].
1 (default): Large reduction in dynamic range.
1/2: Small reduction in dynamic range.
0: DRC off.
Band
With the Band setting, you can choose the DAB band
you want to use, and display the current reception qual-
ity and the reception quality necessary to decode the
current multiplex.
Use the Left and Right Arrow [ ]/[ ] buttons to select
from the following options, and then press [ENTER].
Band III: 5A–13F
L-Band: LA-LW
Display example:
You can adjust the position and direction of the DAB
antenna while monitoring the signal strength on the dis-
play.
To make “Good” appear, adjust the antenna to get the
best signal strength.
Channel If reception is poor, “Bad” is
displayed. If reception is
good, “Good” is displayed.
22
Using Presets
You can store any combination of up to 40 of your
favorite AM, FM, and DAB radio stations as presets.
Using the T-4555:
Using the PRESET buttons:
Using the Auto Scan function:
Using the T-4555:
Presetting Your Favorite Stations
1
Tune into the station that you
want to store as a preset.
2
Press the [MEMORY] button.
The MEMORY indicator appears and
the preset number flashes.
3
While the MEMORY indicator is
displayed (about 8 seconds), use
the PRESET [ ]/[ ] buttons to
select a preset from 1 through 40.
4
Press the [MEMORY] button
again to store the station or
channel.
The station or channel is stored and the
preset number stops flashing.
Repeat this procedure for all of your
favorite radio stations.
PRESET –/+
AUTO SCAN
MEMORY
TUNING MODE
AUTO SCAN
PRESET
/
Selecting Presets
To select a preset, use the
T-4555’s PRESET [ ]/[ ] buttons,
or the remote controller’s PRE-
SET [+]/[–] buttons.
Press the [AUTO SCAN] button.
The Auto Scan function automatically
selects and outputs each radio preset in
turn for 5 seconds.
When you hear the station that you
want to listen to, press the [AUTO
SCAN] button again to stop auto scan-
ning.
Deleting Presets
1
Select the preset that you want to
delete.
See the previous section.
2
While holding down the [MEM-
ORY] button, press the [TUNING
MODE] button.
The preset is deleted and its number
disappears from the display.
Remote controller
Remote controller
23
Changing the Remote ID
If the T-4555’s remote controller interferes with other
Onkyo components located in the same room, you can
change the remote control ID. You can select remote
control ID #1, #2, or #3. By default, the remote control
ID is set to #1. If you change the ID, you must also
change the ID on the remote controller to match, as
explained below, otherwise, the remote controller won’t
work.
Changing the T-4555’s Remote ID
Changing the Remote Controller’s ID
Note:
The remote controller and T-4555 must be set to the
same remote control ID. Otherwise, you won’t be
able to control the T-4555 with the remote controller.
1
Press the [SETUP] button.
2
Use the Up and Down Arrow
[ ]/[ ] buttons to select “Hard-
ware Setup, and then press
[ENTER].
With some tuner boards, there will
only be one option available and you
won’t need to use the Up and Down
Arrow [ ]/[ ] buttons.
3
Use the Up and Down Arrow
[ ]/[ ] buttons to select
“Remote ID.
With some tuner boards, there will
only be one option available and you
won’t need to use the Up and Down
Arrow [ ]/[ ] buttons.
SETUP
///
ENTER
Number buttons
RETURN
Remote controller
Remote controller
Remote controller
4
Use the Left and Right Arrow
[ ]/[ ] buttons to change the
remote ID.
You can select ID #1 (default), #2, or
#3.
5
Press the [SETUP] button.
Once you’ve changed the T-4555’s
remote ID, the remote controller will
no longer control the T-4555, so you
must change the remote controller’s ID
to match, as explained below.
1
Before changing the remote con-
troller’s ID, change the T-4555’s
ID first (see above).
2
Press the remote controller’s
[RETURN] button.
3
While pressing and holding
down the remote controller’s
[RETURN] button, press number
button [1], [2], or [3] for 3 sec-
onds to select ID #1, #2, or #3
respectively.
4
Check whether the remote con-
troller operates the T-4555 prop-
erly.
Remote controller
Remote controller
Remote controller
Remote controller
24
Optional Tuner Boards
The following optional tuner boards are available for the T-4555:
•For T-4555 European model: C-DAB board (AM/FM/DAB tuner)
•For T-4555 U.K. model: C-AMFM board (AM/FM tuner)
Caution:
Before installing or removing a board, be sure to turn off the T-4555 and unplug the power cord from the wall outlet.
Failure to do so could seriously damage your equipment.
In most cases, you do not need to perform the following
procedure. However, if the purchased board is the
worldwide model and you plan to use it in Europe or
U.K., you must change the AM Frequency setting to
9 kHz steps. Follow the procedure below after you
install the board.
Product number: C-AMFM
Provides terminals for FM and AM tuners.
Product number: C-DAB
Provides terminals for DAB, FM stereo and AM tuners.
Board slot
AM Frequency Step Setup
1
Press the [SETUP] button.
2
Use the Up and Down Arrow
[ ]/[ ] buttons to select “Hard-
ware Setup, and then press
[ENTER].
With some tuner boards, there will
only be one option available and you
won’t need to use the Up and Down
Arrow [ ]/[ ] buttons.
Remote controller
Remote controller
3
Use the Up and Down Arrow
[ ]/[ ] buttons to select “AM
Freq.
With some tuner boards, there will
only be one option available and you
won’t need to use the Up and Down
Arrow [ ]/[ ] buttons.
4
Use the Left and Right Arrow
[ ]/[ ] buttons to select:
9 kHz: Select if 9 kHz steps are used
in your area.
10 kHz: Select if 10 kHz steps are
used in your area.
5
Press the [SETUP] button.
Remote controller
Remote controller
Remote controller
25
Optional Tuner Boards—Continued
Use the Allen wrench, hexagonal socket head screws,
removal thumbscrews, and so on supplied with the
board.
Installing a Board
1
Turn off the T-4555, and then unplug the
power cord from the wall outlet.
2
Use the supplied Allen wrench to unscrew
the two hexagonal socket head screws
that are securing the existing board or
blanking plate.
3
Screw the supplied removal thumbscrews
into the two holes just below the holes
that were used by the hexagonal socket
head screws. Screw them in about 3/16"
(5 mm). Hold and pull both of the thumb-
screws to remove the board.
4
Carefully remove the board from its bag.
To prevent electrostatic
damage, hold the board by
its panel, taking care not
to touch any of the com-
ponents or the underside
of the circuit board with
your bare hands.
75
75
5
Insert the board between the guide rails
and push it in.
When the board meets the internal connector,
apply a little more pressure so that the board
plugs fully into the connector. Make sure the
board’s panel is flush with the T-4555’s rear
panel.
6
Use the Allen wrench to screw tight the
two hexagonal socket head screws so
that the board is secure.
Be sure to fully tighten the screws. If they are
loose, the ground connection between the board
and the T-4555 may be inadequate, resulting in
noise or failure.
Caution:
If any of the screws use washers, be sure to reuse
them when installing or removing a board.
26
Troubleshooting
If you have any trouble using the T-4555, look for a solution in this section.
Can’t turn on the T-4555.
Make sure that the power cord is properly plugged into the wall outlet (see page 15).
Unplug the power cord from the wall outlet, wait 5 seconds or more, then plug it in again.
There’s no sound.
Make sure your amplifier’s volume control is not set to minimum.
Check all connections and correct as necessary (see pages 10 to 14).
Reception is noisy, stereo FM reception suffers from hiss, or the STEREO indicator doesn’t light up when tuned
to a stereo FM station.
Check the antenna connections (see page 10).
Change the position of the antenna (see page 16).
•Move the T-4555 away from a nearby TV or computer.
Cars or airplanes can cause noisy interference.
The radio signal will be weakened if it has to pass through a concrete wall before reaching the antenna.
•Try selecting Manual Tuning mode (mono) (see page 15).
•Move power cords and speaker cables as far away as possible from the antenna.
When listening to an AM station, noise may be heard when you operate the remote controller.
If none of the above improves the reception, install an outdoor antenna (see page 11).
If a power outage occurs or the power cable is disconnected:
If the preset stations are lost, preset them again (see page 22).
Can’t adjust the frequency of the radio.
Use the TUNING/CH [ ]/[ ] buttons to change the frequency of the radio (see page 15).
RDS doesn’t work.
The FM station you are tuned to doesn’t support RDS.
Install an outdoor FM antenna (see page 11).
Change the position or direction of your outdoor FM antenna (see page 11).
•Move the FM antenna as far away as possible from fluorescent lights (see page 11).
Power
Audio
Tuner
If you can’t resolve the issue yourself, try resetting the T-4555 before contacting your Onkyo dealer.
To reset the T-4555 to its factory defaults, turn it on and, while holding down the
[MEMORY] button, press the [STANDBY/ON] button. “Clear” will appear on the
display and the T-4555 will enter Standby mode.
Note that resetting the T-4555 will delete your radio presets and custom settings.
27
Troubleshooting—Continued
The remote controller doesn’t work properly.
Make sure the batteries have been installed with the correct polarity (+/–) (see page 9).
Replace both batteries with new ones. (Do not mix different types of batteries or new and old batteries.)
The remote controller is too far away from the T-4555, or there’s an obstacle between them (see page 9).
The T-4555’s remote control sensor is being subjected to bright light (inverter-type fluorescent light or sunlight).
The T-4555 is located behind the glass doors of a audio rack or cabinet.
The T-4555 and remote controller may be set to different remote control IDs. Set the T-4555’s remote control ID first,
and then set the remote controller to the same ID (see page 23).
Interactive control with other Onkyo -capable components is not working.
Make sure the cables and analog audio cables are connected correctly (see page 12). Connecting only an cable
won’t work.
Specifications
Specifications and features are subject to change without notice.
Remote Controller
Others
The T-4555 contains a microcomputer for signal processing and control functions. In very rare situations, severe
interference, noise from an external source, or static electricity may cause it to lock up. In the unlikely event that this
should happen, unplug the power cord, wait at least 5 seconds, and then plug it again.
General
Power Supply: AC 230 V, 50 Hz
Power Consumption: 14.5 W (when C-DAB board is used)
Stand-by Power Consumption: 0.45 W
Dimensions (W × H × D): European model: 435 × 81 × 310 mm, U.K. model: 435 × 81 × 315 mm
Weight: European model: 4.6 kg, U.K. model: 4.7 kg
FM
Tuning frequency range: 87.5–108.0 MHz
Usable sensitivity: Stereo: 22.2 dBf (IHF) Mono: 15.2 dBf (IHF)
Signal-to-noise ratio: Stereo: 67 dB (IHF-A) Mono: 73 dB (IHF-A)
THD (total harmonic distortion): Stereo: 0.5% (1 kHz) Mono: 0.3% (1 kHz)
Stereo separation: 40 dB (1 kHz)
AM
Tuning frequency range: 522–1611 kHz
Usable sensitivity: 300 µV
Signal-to-noise ratio: 40 dB
THD (total harmonic distortion): 0.7%
DAB (U.K. model only)
Tuning frequency range: 174.928–239.200 MHz
Frequency response: 20 Hz–20 kHz
Signal-to-noise ratio: 94 dB
THD (total harmonic distortion): 0.09%
28
SN 29344319
I0608-1
Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN
Tel: 072-831-8023 Fax: 072-831-8124
ONKYO U.S.A. CORPORATION
18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.
Tel: 201-785-2600 Fax: 201-785-2650 http://www.us.onkyo.com/
ONKYO EUROPE ELECTRONICS GmbH
Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY
Tel: +49-8142-4401-0 Fax: +49-8142-4401-555 http://www.eu.onkyo.com/
ONKYO EUROPE UK Office
Suite 1, Gregories Court, Gregories Road, Beaconsfield, Buckinghamshire, HP9 1HQ
UNITED KINGDOM Tel: +44-(0)1494-681515 Fax: +44(0)-1494-680452
ONKYO CHINA LIMITED
Unit 1&12, 9/F, Ever Gain PlazaTower 1, 88, Container Port Road, Kwai Chung,
N.T., HONG KONG Tel: 852-2429-3118 Fax: 852-2428-9039
http://www.ch.onkyo.com/
(C) Copyright 2006 ONKYO CORPORATION Japan. All rights reserved.
http://www.onkyo.com/
HOMEPAGE
* 2 9 3 4 4 3 1 9 *
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo t-4555 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo t-4555 in the language / languages: English as an attachment in your email.

The manual is 1,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo t-4555

Onkyo t-4555 User Manual - English, German, Dutch, Swedish - 88 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info