462136
28
Zoom out
Zoom in
Previous page
1/32
Next page
28
Troubleshooting
If you have any trouble using the T-433, look for a solution here. If you can’t resolve the issue yourself, contact your
Onkyo dealer.
Can’t turn on the T-433.
Make sure that the power cord is properly plugged into the wall outlet (page 11, 14).
Unplug the power cord from the wall outlet, wait five seconds or more, then plug it in again.
The T-433 turns off unexpectedly.
If the sleep timer has been set, and the TIMER indicator is shown on the display, the T-433 will turn off automatically
after a specified period.
When timed playback or recording finishes, the T-433 automatically switches to Standby mode.
There’s no sound.
The T-433 is not connected properly. Check all connections and correct as necessary.
The wrong input source is selected on your amplifier. Check your amplifier’s input source setting. Refer to your
amplifier’s manual.
Check if the A-933’s MAIN IN function is on. Refer to the A-933’s instruction manual.
Make sure the amplifier’s volume control is not set to minimum.
Reception is noisy, stereo FM reception suffers from hiss, the Auto Preset function doesn’t preset all stations,
or the ST indicator doesn’t light up when tuned to a stereo FM station.
Check the antenna connections.
Change the position of the antenna.
•Move the T-433 away from a nearby TV or computer.
•Move power cords and speaker cables as far away as possible from the tuner’s antenna.
Cars or airplanes can cause noisy interference.
The radio signal will be weakened if it has to pass through a concrete wall before reaching the antenna.
•Try setting FM mode to mono.
When listening to an AM station, noise may be heard when you operate the remote controller.
If none of the above improves the reception, install an outdoor antenna.
Timed playback or recording doesn’t work.
Make sure the clock has been set correctly. If the clock has not been set, timed playback or recording is not possible.
If a component is On at the specified start time, the timer will have no effect, so be sure to set the component to
Standby beforehand.
If the settings of two or more timers overlap, some of the timers will not work, so make sure they do not overlap.
Make sure that the and audio cables are connected properly.
Check the settings on the playback and recording components. (Timer recording is not possible with a CDR.)
•For timed recording with an MD recorder, use its analog audio input.
The A-933’s remote controller doesn’t work.
Point the remote controller at the A-933’s remote sensor (page 9).
•To use , you must make an connection and an audio connection between the A-933 and T-433 (page 11).
Check if the A-933’s MAIN IN function is on. Refer to the A-933’s instruction manual.
Power
Audio
Radio
Remote Controller
The T-433 contains a microcomputer for signal processing and control functions. In very rare
situations, severe interference, noise from an external source, or static electricity may cause it to
lockup. In the unlikely event that this should happen, unplug the power cord, wait at least five
seconds, and then plug it again.
To reset the T-433 to its factory defaults, turn it on and, while holding down the [MEMORY] button,
press the [STANDBY/ON] button. “CLEAR” will appear on the display and the T-433 will enter
Standby mode.
*En_T433_02.fm Page 28 Tuesday, February 15, 2005 3:09 PM
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo T-433 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo T-433 in the language / languages: English as an attachment in your email.

The manual is 1,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo T-433

Onkyo T-433 User Manual - German, Dutch - 92 pages

Onkyo T-433 User Manual - French, Italian - 92 pages

Onkyo T-433 User Manual - Swedish - 92 pages

Onkyo T-433 User Manual - Spanish - 92 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info