601422
150
Zoom out
Zoom in
Previous page
1/156
Next page
150
Troubleshooting
—Continued
Cant get 6.1 or 7.1 playback?
If no surround back speakers are connected, or Zone 2/3 is
being used, 6.1 and 7.1 playback is not possible.
If the SB Mode (5ch) is available in any sub-menu of the
Listening Mode Setup menu, make sure that it is not set
to Off (pages 106-112).
The volume cannot be set above 99?
When the levels of all speakers have been calibrated (page
94), the maximum volume setting may change.
Noise can be heard?
Using cable ties to bundle audio cables with power cords,
speaker cables, and so on may degrade the audio perfor-
mance, so dont do it.
An audio cable may be picking up interference. Try reposi-
tioning your cables.
The Late Night function doesnt work?
Make sure the source material is Dolby Digital (page 56).
The multichannel input doesnt work?
Check the MULTI-CH IN connections (page 66).
Make sure that the multichannel input is assigned to the
correct input source (page 66).
Set the audio input signal format to Multich (page 67).
About DTS signals
When DTS program material ends and the DTS bitstream
stops, the RDC-7.1 remains in DTS listening mode and the
DTS indicator remains on. This is to prevent noise when
you use the pause, fast forward, or fast reverse function on
your player. If you switch your player from DTS to PCM,
because the RDC-7.1 does not switch formats immediately,
you may not hear any sound, in which case you should stop
your player for about three seconds, and then resume play-
back.
With some CD and LD players, you wont be able to play-
back DTS material properly even though your player is
connected to a digital input on the RDC-7.1. This is usually
because the DTS bitstream has been processed (e.g., output
level, sampling rate, or frequency response changed) and
the RDC-7.1 doesnt recognize it as a genuine DTS signal.
In such cases, you may hear noise.
When playing DTS program material, using the pause, fast
forward, or fast reverse function on your player may pro-
duce a short audible noise. This is not a malfunction.
Theres no picture?
Make sure that all video connecting plugs are pushed in all
the way.
Make sure that each video component is properly con-
nected.
Make sure that the proper setting is made for the Video
Assign sub-menu under the Input Setup menu (page
99).
On your TV, make sure that the video input to which the
RDC-7.1 is connected is selected.
While the Pure Audio listening mode is selected, the video
circuits are turned off and the RDC-7.1 outputs no video
signals.
The onscreen menus (OSD) dont appear, or they
appear in an odd position?
Make sure that the proper setting is made for the Video
Output Assign sub-menu under the Speaker/Output
Setup menu (page 92).
Make sure that the proper setting is made for the OSD
Setup sub-menu under the Preference menu (page 120).
On your TV, make sure that the video input to which the
RDC-7.1 is connected is selected.
Reception is noisy, FM stereo reception is noisy, or
the FM STEREO indicator doesnt appear?
Relocate your antenna.
Move the RDC-7.1 away from your TV or computer.
Press the [Tuning Mode] button to turn off the AUTO
indicator, bringing the FM mode to monaural (page 62).
When listening to an AM station, operating the remote con-
troller may cause noise.
Passing cars and airplanes can cause interference.
Concrete walls weaken radio signals.
If nothing improves the reception, install an outdoor
antenna.
When the RDC-7.1 is unplugged or a power failure
occurred:
Normally, the built-in memory retains its contents for 2
weeks. If it loses radio presets, make the presets again.
The remote controller doesnt work?
Make sure that the batteries are installed with the correct
polarity (page 9).
Install new batteries. Dont mix different types of batteries
or old and new batteries (page 9).
Make sure that the remote controller is not too far away
from the RDC-7.1, and that theres no obstruction between
the remote controller and the RDC-7.1s remote control
sensor (page 9).
Make sure that the RDC-7.1 is not subjected to direct sun-
shine or inverter type uorescent lights. Relocate if neces-
sary.
If the RDC-7.1 is installed in a rack or cabinet with colored
glass doors, the remote controller may not work reliably
when the doors are closed.
Make sure youve selected the correct remote controller
mode (page 51).
When using the remote controller to control other manufac-
turers AV components, some buttons may not work as
expected.
Make sure youve entered the correct remote control ID.
If you change the remote controllers transmission signal
format to RF, be sure to select the same ID as the RF
receiver.
Cant control other components?
If its an IntegraRESEARCH component, make sure that
the cable and analog audio cable (RCA/phono) are
connected properly. Connecting only an cable wont
work (page 45).
Make sure youve selected the correct remote controller
mode (page 51).
Video
Tuner
Remote Controller
150


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo RDC-7.1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo RDC-7.1 in the language / languages: English as an attachment in your email.

The manual is 12,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo RDC-7.1

Onkyo RDC-7.1 User Manual - German - 156 pages

Onkyo RDC-7.1 User Manual - Dutch - 156 pages

Onkyo RDC-7.1 User Manual - French - 156 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info