61148
130
Zoom out
Zoom in
Previous page
1/134
Next page
130
Troubleshooting—Continued
Can’t record
On your recorder, make sure the correct input is
selected.
To prevent signal loops and damage to the AV control-
ler, input signals are not fed through to outputs with
the same name (e.g., TAPE IN to TAPE OUT or
VCR/DVR IN to VCR/DVR OUT).
When the Pure Audio listening mode is selected,
video recording is not possible because no video sig-
nals are output. Select another listening mode.
There’s no sound
Only components connected to analog inputs can be
played in Zone 2 and Zone 3.
The sound changes when I connect my head-
phones
When a pair of headphones is connected, the listening
mode is set to Stereo, unless it’s already set to Stereo,
Mono, Direct, or Pure Audio.
The speaker volume cannot be set as required
When the Automatic Speaker Setup function is used,
or the volume is adjusted on the onscreen setup
menus, the maximum possible volume setting may
change.
The speaker distance cannot be set as required
In some cases, corrected values suitable for home the-
ater use may be set automatically.
The display doesn’t work
The display is turned off when the Pure Audio listen-
ing mode is selected.
How do I change the language of a multiplex
source
On the “Audio Adjust” menu, change the “Multiplex”
setting to “Main” or “Sub” (page 98).
The u functions don’t work
To use u, you must make an u connection and an
analog audio connection (RCA) between the compo-
nent and AV controller, even if they are connected dig-
itally (page 44).
While Zone 2 or Zone 3 is selected, the u functions
don’t work.
The functions Auto Power On/Standby and
Direct Change don’t work for components con-
nected via u
These functions don’t work when Zone 2 is turned on.
When performing “Automatic Speaker Setup”,
the measurement fails showing the message
“Ambient noise is too high”.
This can be caused by any malfunction in your speaker
unit. Check if the unit produces normal sounds.
Recording
Zone 2/Zone 3
Others
The AV controller contains a microcomputer for signal
processing and control functions. In very rare situations,
severe interference, noise from an external source, or
static electricity may cause it to lockup. In the unlikely
event that this happens, unplug the power cord from the
wall outlet, wait at least 5 seconds, and then plug it back
in again.
Onkyo is not responsible for damages (such as CD
rental fees) due to unsuccessful recordings caused by
this unit’s malfunction. Before you record important
data, make sure that the material will be recorded cor-
rectly.
For North American model, set the AV controller to
Standby before disconnecting the power cord from the
wall outlet. For other models, set the AV controller to
Standby and the POWER switch to OFF before discon-
necting the power cord.
130


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo PR-SC886 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo PR-SC886 in the language / languages: English as an attachment in your email.

The manual is 7,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info