462083
92
Zoom out
Zoom in
Previous page
1/108
Next page
92
En
Firmware Update
To update the firmware of the AV controller, you can
choose from the following two methods: update via
network, or update via USB storage. Choose the one that
best suits your environment. Before proceeding with the
update, please read the corresponding explanations
carefully.
Update via network
You need a wired Internet connection to update the
firmware.
Update via USB storage ( page 93)
Please prepare a USB storage device such as a USB
flash memory stick. You need at least 32 MB of
available space to update the firmware.
Note
Check the network connection before updating.
Do not touch the any cable or device connected to the AV
controller during the update process.
Do not attempt to access the AV controller from your PC while
it is being updated.
Do not shutdown the power of the AV controller while it is being
updated.
The storage media in the USB card reader may not work.
If the USB device is partitioned, each section will be treated as
an independent device.
If the USB device contains a lot of data, the AV controller may
take a while to read it.
Operation is not guaranteed for all USB devices, which includes
the ability to power them.
Onkyo takes no responsibility whatsoever for the loss or damage
of data resulting from the use of a USB device with the AV
controller. Onkyo recommends that you back up your important
music files beforehand.
If you connect a USB hard disk drive to the USB port, Onkyo
recommends that you use its AC adapter to power it.
USB hubs and USB devices with hub functions are not
supported. Do not connect your USB device via a USB hub.
USB devices with security functions are not supported.
The AV controller allows you to update the firmware using
network connection on the rear panel.
Note
Make sure your AV controller and TV are turned on and an
Ethernet cable is connected to the rear panel of the AV
controller.
Never unplug or turn off the AV controller while it is being
updated.
Never plug or unplug an HDMI or Ethernet cable during the
update process.
Do not attempt to access the AV controller from your PC while
it is being updated.
Never unplug the power cord during the update process.
It takes maximum 60 minutes to complete the firmware update.
The AV controller will retain all your settings after the update is
finished.
Before you start
• Set the “HDMI Control(RIHD)” setting to “Off
( page 67).
Turn off the controller device connected via RS232C and
via Ethernet network.
Turn off Zone 2 and Zone 3.
Stop playback of contents from Internet Radio,
iPod/iPhone, USB or servers, etc.
Update procedure
Limitation of liability
The program and accompanying online documentation
are furnished to you for use at your own risk. Onkyo
will not be liable and you will have no remedy for
damages for any claim of any kind whatsoever
concerning your use of the program or the
accompanying online documentation, regardless of
legal theory, and whether arising in tort or contract. In
no event will Onkyo be liable to you or any third party
for any special, indirect, incidental, or consequential
damages of any kind, including, but not limited to,
compensation, reimbursement or damages on account of
the loss of present or prospective profits, loss of data, or
for any other reason whatsoever.
See the Onkyo web site for latest information.
Updating the Firmware via Network
1
Press RECEIVER followed by SETUP on the
remote controller.
The Setup menu will be displayed on the TV screen.
The procedures thereafter can also be performed on
the AV controller by using its SETUP, arrow and
ENTER buttons.
2
Select “Hardware Setup” and press ENTER.
3
Select “Firmware Update” and press ENTER.
Note that the “Firmware Update” option will be
grayed out for a short while after the AV controller
is turned on. Please wait until it becomes operable.
4
Select “via NET” and press ENTER.
5
Select “Update” and press ENTER.
The update process will begin.
During the update process, the on-screen display
may disappear depending on the updated program.
When this occurs, you can still view the update
progress on the front display of the AV controller.
The on-screen display will reappear after the update
is complete, and upon turning the AV controller off
and on again.
6
The message “Completed!” appears on the front
display of the AV controller, indicating that the
update has been completed.
92


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo PR-SC5509 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo PR-SC5509 in the language / languages: English as an attachment in your email.

The manual is 4,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo PR-SC5509

Onkyo PR-SC5509 User Manual - German - 212 pages

Onkyo PR-SC5509 User Manual - Dutch - 212 pages

Onkyo PR-SC5509 User Manual - Italian - 212 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info