462127
37
Zoom out
Zoom in
Previous page
1/40
Next page
37
En
Make sure that the USB cable is plugged in firmly
( 15).
• Make sure that the USB driver is installed successfully
( 31).
• Make sure that there is no unsupported file formats or
signals.
The USB cable is unplugged. To stop the blinking of the
display, turn the power ON/OFF, or plug the USB cable
again.
• Make sure that the Onkyo Dock is connected to the
preamplifier properly.
• Make sure that no video content is being played.
Reset the iPod.
When the set ASb starts running, the power of the
Onkyo Dock connected via RI is automatically turned
off ( 35).
• Make sure that the u cable is connected to the
preamplifier correctly.
You need to change the selector name to use u
function ( 33).
• Make sure the correct input source is selected ( 26).
• Make sure the analog audio cable is connected correctly
( 15).
• If your turntable (MM) has a phono built-in preamp,
connect to other analog inputs such as CD IN or
LINE 1 IN.
If your turntable (MM) does not have a phono built-in
preamp, connect a turntable (MM) without a built-in a
phono preamp to PHONO IN ( 19).
Make sure that the ground wire is connected. Otherwise,
it may produce an audible hum and noise.
• Turn each of the components’ power on or off in the
following order.
When turning the power on:
1. Source component
2. Preamplifier (P-3000R)
3. Power Amplifier (M-5000R
*
)
When turning the power off:
1. Power Amplifier (M-5000R
*
)
2. Preamplifier (P-3000R)
3. Source component
*
When using 12V TRIGGER OUT as M-5000R is combined
with P-3000R, the popping noise is reduced by power
management.
Make sure the batteries have been installed with the
correct polarity (+/–) ( 10).
• Replace both batteries with new ones. (Do not mix
different types of batteries or new and old batteries.)
• The remote controller is too far away from the
preamplifier, or there’s an obstacle between them
( 10).
The preamplifier’s remote control sensor is being
subjected to bright light (inverter-type fluorescent light
or sunlight).
The preamplifier is located behind the glass doors of a
audio rack or cabinet.
PC Playback
Can’t playing the music files on the PC.
Can’t display the sampling rate correctly.
The USB selector on the display flashes.
Onkyo Dock
There’s no sound.
Other
Can’t control properly by using the
remote controller.
External Components
No sound is heard from a connected
component.
The sound from record player is
distorted.
A popping noise is produced when the
power is set to ON or OFF.
Remote Controller
The remote controller doesn’t work
properly.
Onkyo is not responsible for damages (such as CD
rental fees) due to unsuccessful recordings caused by
the unit’s malfunction. Before you record important
data, make sure that the material will be recorded
correctly.
The preamplifier contains a microcomputer for
signal processing and control functions. In very rare
situations, severe interference, noise from an external
source, or static electricity may cause it to lockup. In
the unlikely event that this should happen, unplug the
power cord, wait at least 5 seconds, and then plug it
again.
Before disconnecting the power cord from the wall
outlet, set the preamplifier to Standby.
37


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo P-3000R at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo P-3000R in the language / languages: English as an attachment in your email.

The manual is 1,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo P-3000R

Onkyo P-3000R User Manual - German - 76 pages

Onkyo P-3000R User Manual - Dutch - 76 pages

Onkyo P-3000R User Manual - French - 76 pages

Onkyo P-3000R User Manual - Italian - 76 pages

Onkyo P-3000R User Manual - Swedish - 76 pages

Onkyo P-3000R User Manual - Spanish - 76 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info