462127
33
Zoom out
Zoom in
Previous page
1/40
Next page
33
En
Advanced O perations
Custom Setup
You can switch the selector name to DC/DIG to run as the
DOCK selector.
To cancel the assignment
Press DISPLAY again for 3 seconds.
Note
DOCK can be selected for the Digital input source (COAX1,
COAX2, OPT1, OPT2) input selector, but not at the same time.
You can convert the sampling rate of the input digital
signal.
Note
If the sampling rate is greater than 192/176.4 kHz, the sampling
rate conversion will not be applied.
Only analog audio is output by converting sampling rates. No
digital audio is reproduced.
To confirm the current setting value, see “Changing the Display
information” ( 28).
Digital input signals are put through and output on this
preamplifier as is.
•The USB input does not support FS x4 ( 31).
Offset the volume level based on master volume.
You can also use preamplifier’s MODE and Multi jog dial.
See “Using MODE button” to perform this procedure on
the preamplifier ( 29).
Note
The preamplifier will end the setup if there is no operation for
8 seconds.
Changing the Selector Name
1
Select the Digital input source (COAX1, COAX2,
OPT1, OPT2) to change the selector name.
2
Press DISPLAY for 3 seconds.
DC/DIG” is displayed on the display.
DISPLAY
Selecting the Sampling Rate
Conversion
1
Press SRC repeatedly on the preamplifier.
` BYPASS (default):
Outputs the input sampling rate at the original
sampling rate.
` FS x2:
Outputs the input sampling rate by converting it
to x2.
` FS x4:
Outputs the input sampling rate by converting it
to x4.
SRC
Setting the Bi-amp Level
1
Press SETUP.
2
Press #/$ to select “BIAMP”.
3
Press ENTER.
4
Press #/$ to adjust the bi-amp level.
The high and low output balance can be adjusted.
The setting has been established.
SETUP
#, $
ENTER
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo P-3000R at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo P-3000R in the language / languages: English as an attachment in your email.

The manual is 1,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo P-3000R

Onkyo P-3000R User Manual - German - 76 pages

Onkyo P-3000R User Manual - Dutch - 76 pages

Onkyo P-3000R User Manual - French - 76 pages

Onkyo P-3000R User Manual - Italian - 76 pages

Onkyo P-3000R User Manual - Swedish - 76 pages

Onkyo P-3000R User Manual - Spanish - 76 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info