686354
71
Zoom out
Zoom in
Previous page
1/99
Next page
71
Front Panel Rear Panel Remote
Contents
Connections
Playback
Setup
2. Speaker
1. Conguration
Change the settings of connection environment of the speakers.
Setting Item Default Value Setting Details
Speaker
Channels
5.1 ch Select "2.1 ch", "3.1 ch", "4.1 ch", "5.1 ch",
"2.1.2 ch" or "3.1.2 ch" to suit the number of
speaker channels connected.
Subwoofer Yes Set whether a subwoofer is connected or not.
"Yes": When a subwoofer is connected
"No": When a subwoofer is not connected
Height Speaker Top Middle Set the speaker type if height speakers are
connected to the SURROUND or HEIGHT
terminals.
Select "Top Middle", "Dolby Speaker (Front)" or
"Front High" according to the type and layout of the
connected speakers.
• If the item cannot be selected even though
connection is correct, check if the setting in
"Speaker Channels" matches the number of
connected channels.
Speaker
Impedance
6 ohms or above Set the impedance (Ω) of the connected speakers.
"4 ohms": When any of the connected speakers
have 4 Ω or more to less than 6 Ω impedance
"6 ohms or above": When the connected speakers
all have 6 Ω or more impedance
For impedance, check the indications on the
back of the speakers or their instruction manual.
2. Crossover
Change the settings of crossover frequencies.
Setting Item Default Value Setting Details
Front 150 Hz Select the crossover frequency from "40 Hz" to
"200 Hz" to start outputting frequencies for each
channel.
"Full Band": Full band will be output.
If "Conguration" - "Subwoofer" is set to "No",
"Front" is xed to "Full Band", and the low
pitched range of the other channels is output
from the front speakers. Refer to the instruction
manual of your speakers to make the setting.
Center 150 Hz Select the crossover frequency from "40 Hz" to
"200 Hz" to start outputting frequencies for each
channel.
"Full Band": Full band will be output.
"Full Band" can be selected only when "Front" is
set to "Full Band".
• If the item cannot be selected even though
connection is correct, check if the setting in
"Conguration" - "Speaker Channels" matches
the number of connected channels.
Height 150 Hz Select the crossover frequency from "40 Hz" to
"200 Hz" to start outputting frequencies for each
channel.
"Full Band": Full band will be output.
"Full Band" can be selected only when "Front" is
set to "Full Band".
• If the item cannot be selected even though
connection is correct, check if the setting in
"Conguration" - "Speaker Channels" matches
the number of connected channels.
71


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo HT-S3910 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo HT-S3910 in the language / languages: English as an attachment in your email.

The manual is 3,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo HT-S3910

Onkyo HT-S3910 User Manual - German - 99 pages

Onkyo HT-S3910 User Manual - Dutch - 99 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info