462101
54
Zoom out
Zoom in
Previous page
1/172
Next page
54
En
OSD Setup
On Screen Display
` On
` Off
This preference determines whether operation details are
displayed on-screen when an AV receiver function is
adjusted.
Even when “On” is selected, operation details may not be
output if the input source is connected to an HDMI IN.
Language
(North American models)
` English
, Deutsch, Français, Español, Italiano,
Nederlands, Svenska
(European models)
` English
, Deutsch, Français, Español, Italiano,
Nederlands, Svenska, 中文
This setting determines the language used for the on-
screen setup menus.
Main menu Hardware Setup
Remote ID
Remote ID
` 1
, 2, or 3
When several Onkyo components are used in the same
room, their remote ID codes may overlap. To differentiate
the AV receiver from the other components, you can
change its remote ID from 1”, to “2” or “3”.
Note
If you do change the AV receiver’s remote ID, be sure to change
the remote controller to the same ID (see below), otherwise, you
won’t be able to control it with the remote controller.
Changing the remote controller’s ID
Tuner
For AM/FM tuning to work properly, you must specify the
AM/FM frequency step used in your area. Note that when
this setting is changed, all radio presets will be deleted.
AM/FM Frequency Step (North American
models)
` 10kHz/200kHz
:
` 9kHz/50kHz:
Select the frequency step according to your area.
AM Frequency Step (European models)
` 10kHz:
` 9kHz
:
Select the frequency step according to your area.
HDMI
HDMI Control(RIHD)
` Off
` On
Turn this setting on to allow
p-compatible
components connected via HDMI to be controlled by the
AV receiver ( page 82).
Note
When the setting is set to “On” and the menu is closed, the
names of connected p-compatible components and
RIHD On” are displayed on the AV receiver.
Search…(name)RIHD On
When the AV receiver cannot receive the name of the
component, it is displayed as “Player
*
” or “Recorder
*
”, etc (“
*
shows up and indicates the number of components, when two or
more are received).
•When an p-compatible component is connected to the
AV receiver via an HDMI cable, the name of the connected
component is displayed on the AV receiver display. For
example, while you are watching TV broadcasting, if you
operate a Blu-ray Disc/DVD player (being powered on) with the
remote control of the AV receiver, the name of the Blu-ray
Disc/DVD player will be displayed on the AV receiver.
•Set it to
Off when a connected piece of equipment is not
compatible or it is unclear whether the equipment is compatible
or not.
If operation is not normal when set to
On, change the setting
to
Off.
Refer to the connected component’s instruction manual for
details.
•WhenHDMI Control(RIHD)” setting is set to “On”, the
power consumption on standby mode slightly increases.
(Depending on the TV status, the AV receiver will enter standby
mode as usual.)
Hardware Setup
1
While holding down RECEIVER, press and hold
down SETUP until the remote indicator lights
(about 3 seconds) ( page 41).
2
Use the number buttons to enter ID 1, 2, or 3.
The remote indicator flashes twice.
54


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo HT-R990 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo HT-R990 in the language / languages: English, French as an attachment in your email.

The manual is 4,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo HT-R990

Onkyo HT-R990 User Manual - German, Dutch, Swedish - 256 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info