535523
44
Zoom out
Zoom in
Previous page
1/52
Next page
44
En
Troubleshooting
If you have any trouble using the AV receiver, look for a
solution in this section. If you can’t resolve the issue your-
self, contact your Onkyo dealer.
Can’t turn on the AV receiver
The STANDBY indicator flashes red
There’s no sound, or it’s very quiet
If you can’t resolve the issue yourself, try resetting the
AV receiver before contacting your Onkyo dealer.
To reset the AV receiver to its factory defaults, turn it
on and, while holding down VCR/DVR, press ON/
STANDBY. “Clear” will appear on the display and
the AV receiver will enter Standby mode.
Note that resetting the AV receiver will delete your
radio presets and custom settings.
To reset the remote controller to its factory defaults,
while holding down RECEIVER, press and hold down
AUDIO until the remote indicator lights (about 3 sec-
onds). Within 30 seconds, press RECEIVER
again.
The on-screen setup menus appear only on a TV that
is connected to the HDMI OUT. If your TV is con-
nected to the MONITOR OUT V or the COMPO-
NENT VIDEO OUT, use the AV receiver’s display
when changing settings.
Power
Make sure that the power cord is properly plugged
into the wall outlet.
Unplug the power cord from the wall outlet, wait five
seconds or more, then plug it in again.
AUDIO
RECEIVER
Remote indicator
The protection circuitry has been activated.
Remove the power cord from the wall outlet immedi-
ately. Disconnect all speaker cables and input
sources, and then leave the AV receiver with its
power cord disconnected for 1 hour. After that,
reconnect the power cord and set the volume to max-
imum. If the AV receiver stays on, set then the vol-
ume to minimum, disconnect the power cord, and
reconnect your speakers and input sources. If the AV
receiver turns off when you set the volume to maxi-
mum, disconnect the power cord, and contact your
Onkyo dealer.
Audio
Press SPEAKERS A or B to turn on the indicator
for the speakers that you want to output sound.
Make sure that the digital input source is selected
properly.
29
Make sure that all audio connecting plugs are pushed
in all the way.
13
Make sure that the inputs and outputs of all compo-
nents are connected properly.
14-16
Make sure that the polarity of the speaker cables is
correct, and that the bare wires are in contact with
the metal part of each speaker terminal.
11
Make sure that the input source is properly selected. 19
Make sure that the speaker cables are not shorting. 11
Check the volume. The AV receiver is designed for
home theater enjoyment. It has a wide volume range,
allowing precise adjustment.
If the MUTING indicator is flashing on the display,
press the remote controller’s MUTING to unmute
the AV receiver.
20
While a pair of headphones is connected to the
PHONES jack, no sound is output by the speakers.
20
If there’s no sound from a DVD player connected to
an HDMI IN, check the DVD player’s output set-
tings, and be sure to select a supported audio format.
Check the digital audio output setting on the con-
nected device. On some game consoles, such as
those that support DVD, the default setting is off.
With some DVD-Video discs, you need to select an
audio output format from a menu.
If your turntable uses an MC cartridge, you must
connect an MC head amp, or an MC transformer.
Make sure that none of the connecting cables are
bent, twisted, or damaged.
Not all listening modes use all speakers. 25
Specify the speaker distances and adjust the individ-
ual speaker levels.
30
The input signal format is set to PCM or DTS. Set it
to Auto.
36
44


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo HT-R538 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo HT-R538 in the language / languages: English as an attachment in your email.

The manual is 1,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo HT-R538

Onkyo HT-R538 User Manual - German - 2 pages

Onkyo HT-R538 User Manual - Dutch - 104 pages

Onkyo HT-R538 User Manual - French, Spanish - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info