463986
61
Zoom out
Zoom in
Previous page
1/64
Next page
61
Troubleshooting
If you have any trouble using the AV receiver, look for a
solution in this section.
Can’t turn on the AV receiver
Make sure that the power cord is plugged into the wall
outlet properly.
Unplug the power cord from the wall outlet, wait 5
seconds or more, then plug it in again.
The AV receiver turns off as soon as it’s turned
on
The amp protection circuit has been activated.
Remove the power cord from the wall outlet immedi-
ately. Disconnect all speaker cables and input sources,
and leave the AV receiver with its power cord discon-
nected for 1 hour. After that, reconnect the power cord
and set the volume to maximum. If the AV receiver
stays on, set the volume to minimum, disconnect the
power cord, and reconnect your speakers and input
sources. If the AV receiver turns off when you set the
volume to maximum, disconnect the power cord, and
contact your Onkyo dealer.
There’s no sound or it’s very quiet
Make sure that the digital input source is selected
properly (page 37). Press the [DIGITAL INPUT] but-
ton repeatedly.
Make sure that all audio connecting plugs are pushed
in all the way (page 20).
Make sure that the polarity of the speaker cables is
correct, and that the bare wire is in contact with metal
part of each speaker terminal (page 17)
Make sure that the speaker cables are not shorting.
Check the volume. It can be set to MIN, 1 through 79,
or MAX (page 38). The AV receiver is designed for
home theater enjoyment and has a wide volume range
for precise adjustment.
If the MUTING indicator is shown on the display,
press the remote controller’s [MUTING] button to
unmute the AV receiver (page 44).
While a pair of headphones is connected, no sound is
output by the speakers (page 45).
Check the digital audio output settings on the con-
nected device. On some games consoles, such as those
that can play DVDs, the default setting is off.
•With some DVD-Video discs, you need to select an
audio format from a menu.
If your turntable doesn’t have a phono preamp built-in,
you must connect one between it and the AV receiver.
If your turntable uses an MC cartridge, you must con-
nect an MC head amp, or an MC transformer and a
phono preamp.
Make sure that the speaker setup microphone is not
still connected.
Specify the speaker distances and adjust the individual
speaker levels (page 55).
The input signal format is set to PCM or DTS. Set it to
Auto (page 57).
Audio from a DVD player connected via HDMI is not
output by the speakers connected to the AV receiver.
To listen to this audio through the speakers, in addition
to an HDMI connection, you’ll also need to make a
separate analog or digital audio connection (page 25).
If your DVD player is connected via HDMI and your
TV produces no sound, check your DVD player’s
audio output settings, and be sure to select an audio
format that’s supported by your TV.
Only the front speakers produce sound
When the Stereo or Mono listening mode is selected,
only the front speakers and subwoofer produce sound.
Make sure the speakers are configured correctly
(page 52).
Only the center speaker produces sound
If you use the Pro Logic II Movie, Pro Logic II Music,
or Pro Logic II Game listening mode with a mono
source, such as an AM radio station or mono TV pro-
gram, the sound is concentrated in the center speaker.
Make sure the speakers are configured correctly
(page 52).
The surround speakers produce no sound
When the Stereo or Mono listening mode is selected,
the surround speakers produce no sound (page 47).
Depending on the source and current listening mode,
not much sound may be produced by the surround
speakers. Try selecting another listening mode.
Make sure the speakers are configured correctly
(page 52).
Power
Audio
If you can’t resolve the issue yourself, try resetting
the AV receiver before contacting your Onkyo dealer.
To reset the AV receiver to its factory defaults,
turn it on and, while holding down the [VCR/DVR]
button, press the [STANDBY/ON] button. “Clear”
will appear on the display and the AV receiver will
enter Standby mode.
Note that resetting the AV receiver will delete your
radio presets and custom settings.
STANDBY/ON
VCR/DVR
61


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo HT-R508 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo HT-R508 in the language / languages: English as an attachment in your email.

The manual is 2,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo HT-R508

Onkyo HT-R508 User Manual - German - 132 pages

Onkyo HT-R508 User Manual - Dutch - 132 pages

Onkyo HT-R508 User Manual - French - 132 pages

Onkyo HT-R508 User Manual - Italian - 132 pages

Onkyo HT-R508 User Manual - Spanish - 132 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info