601883
9
Zoom out
Zoom in
Previous page
1/20
Next page
Step 2: Setting Up
En-9
Operation: Use the remote controller of this unit to
operate the menus shown on the TV screen. To display the
guidance, you need to make HDMI connection between
the unit and TV. Select the item with the cursor buttons of
the remote controller and press ENTER to confirm your
selection. To return to the previous screen, press RETURN.
1 Turning the Power On
Connect the power cord to the outlet. Press z ON/
STANDBY on the main unit or z RECEIVER on the remote
controller to turn the unit on or to standby mode.
When the unit is turned on, a large instantaneous
current may flow affecting functionality of the computer
and other devices. It is recommended to use a separate
outlet from that for the computer or such other sensitive
devices.
2 Making Automatic Speaker Setting
The AccuEQ Room Calibration function, our proprietary
technology, measures the test tone coming from each
speaker with the supplied speaker setup microphone,
setting of the number of speakers, volume level, each
speaker's optimum crossover frequencies, and distance
from the primary listening position, and also enables
correction of distortion caused by the acoustic environment
of the room.
You cannot return to the previous screen during speaker
setup, even if you press RETURN.
1� Place the speaker setup microphone�
Before starting the procedure, refer to the figure and
place the supplied speaker setup microphone at the
measurement position .
Listening area
Measurement position with
microphone
¼ Correct measurement will not be possible if the microphone is held
by hand. Measurement is not possible if headphones are being used.
¼ The subwoofer sound may not be detected since it is extremely
low frequencies. Set the subwoofer volume to around the half of its
maximum volume and make its frequency to the maximum level.
¼ Measurement may be interrupted if there is ambient noise or radio
frequency interference. Close the window and turn off the home
appliance and fluorescent light.
2� Connect the speaker setup microphone to the
SETUP MIC jack of the unit�
SETUP MIC jack
Speaker
setup
microphone
HT-R494_BAS_En_SN29401998_1503xx.indd 9 2015/03/12 15:07:43
9


Need help? Post your question in this forum.

Forumrules
1

Forum

onkyo-ht-r494

Reset search

  • What connection port do you use when connecting a record deck (with integrated pre-amp)? Submitted on 12-3-2017 at 15:40

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo HT-R494 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo HT-R494 in the language / languages: English as an attachment in your email.

The manual is 1,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo HT-R494

Onkyo HT-R494 User Manual - German, Dutch - 72 pages

Onkyo HT-R494 User Manual - French - 36 pages

Onkyo HT-R494 User Manual - Italian, Swedish - 72 pages

Onkyo HT-R494 User Manual - Spanish - 36 pages

Onkyo HT-R494 User Manual - Finnish - 72 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info