136788
19
Zoom out
Zoom in
Previous page
1/60
Next page
19
Connecting the DV-SP501
—Continued
The setup described here is a basic setup that allows you to play discs using just the cables supplied with the player. In
this setup, stereo audio is played through the speakers in your TV.
This player is equipped with copy protection technol-
ogy. Do not connect this player to your TV via a VCR
using AV cables, as the picture from this player will
not appear properly on your TV. (This player may also
not be compatible with some combination TV/VCRs
for the same reason; refer to the manufacturer for more
information.)
If your TV only has a mono audio input, connect it to
the DV-SP501’s MONO ANALOG AUDIO OUT-
PUT.
Other than European model
When connecting to your TV as shown above, do not
set the “Component Out” setting (page 45) to “Pro-
gressive.” (Other than European models.)
1. Connect the VIDEO OUTPUT and AUDIO OUT-
PUT ANALOG L/R jacks to a set of A/V inputs
on your TV.
Use the supplied audio/video cable, connecting the
red and white plugs to the audio outputs and the yel-
low plug to the video output. Make sure you match
up the left and right audio outputs with their corre-
sponding inputs for correct stereo sound.
See the following page if you want to use a compo-
nent or S-Video cable for the video connection.
2. Connect the supplied AC power cord to the AC
INLET, then plug into a power outlet.
Notes:
Before unplugging the player from the power outlet,
make sure you first switch it into standby using either
the front panel STANDBY/ON button, or the remote
controller, and wait of the “GOOD BYE” message to
disappear from the player’s display.
•For the above reasons, do not plug this player into a
switched power supply found on some amplifiers and
AV receivers.
Other than North American model and European
models
When TV System is set to “AUTO” or “NTSC”, and
playing an NTSC disc only: When “Component Out”
(page 45) is set to “Progressive”, there is no video out-
put from the “VIDEO OUTPUT” (composite) and
“S VIDEO” jacks. If you want to display video on
more than one monitor simultaneously, make sure that
it is set to Interlace. Switch the player to standby then,
using the front panel controls, press STANDBY/ON
while pressing to switch the player back to
“Interlace.
North American model
When “Component Out” (page 45) is set to “Progres-
sive”, there is no video output from the “VIDEO
OUTPUT” (composite) and “S VIDEO” jacks. If you
want to display video on more than one monitor simul-
taneously, make sure that it is set to Interlace. Switch
the player to standby then, using the front panel con-
trols, press STANDBY/ON while pressing to
switch the player back to “Interlace.
Basic Setup
AC
INLET
COMPONENT
P
B
P
R
Y
VIDEO
S
VIDEO
REMOTE
CONTROL
MONO
L
R
DIGITAL
OPTICAL COAXIAL
AUDIO
OUTPUT
AUDIO
OUTPUT
ANALOG
VIDEO
OUTPUT
DVD
PLAYER
MODEL NO. DV
-
SP
501
L
R
ANALOG
INPUT
VIDEO IN
To power outlet
TV
DV-SP501_En.book Page 19 Tuesday, May 20, 2003 4:17 PM
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo dv sp 501 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo dv sp 501 in the language / languages: English as an attachment in your email.

The manual is 2,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info