138965
59
Zoom out
Zoom in
Previous page
1/64
Next page
59
4
5
6
7
Press and hold down the button on
the other remote control unit that
corresponds to the command you
want to program until the SEND/
LEARN indicator flashes twice to
indicate that the command has
been successfully programmed.
After flashing twice, the SEND/LEARN indicator
lights up again.
Repeat steps 3 and 4 to program
other commands within the same
mode.
Repeat step 2 to 4 to program
commands to the other mode.
Press the MODE button (DVD or
RECVR) that you pressed in step 2
to complete the programming.
Use the remote controller to
perform the newly learned
command to confirm that it was
learned correctly.
Notes
Some buttons have already been programmed to control functions of an
Onkyo receiver. Therefore, it is recommended to program additional
functions of the receiver that are not already programmed in the remote
controller.
If no buttons are pressed for more than 30 seconds during the
programming, or if you perform an invalid operation, the SEND/LEARN
indicator flashes three times quickly and the remote controller exits the
programming mode. Resume programming from step 2.
If you perform an invalid operation during programming, the SEND/
LEARN indicator flashes three times quickly and the remote controller
exits the programming mode. Resume from Step 2.
When you want to program a command to a button to which you have
already programmed a command, simply follow the same procedure and
programming for that button will be overwritten.
The remote controller uses infrared rays to send its commands, as do most
other remote control units. Though most remote control units can be
memorized by the remote controller, be aware that some remote control
units use a system that is quite different from the remote controller and
therefore may not be able to be programmed.
Some remote control units have a single button that performs multiple
functions (for example, the function may change each time the button is
pressed). If this is the case, each function must be programmed to a
separate button on the remote controller.
Once you have programmed the commands from the other remote control
unit, refer to the instructions supplied with the other component to operate.
Make sure that both the remote controller and the other remote control unit
have new batteries. If either of them has batteries that are low, you may not
be able to program the commands of the other remote control unit properly
into the remote controller.
After programming another function to the ZOOM ON button or ZOOM
+/– buttons, it is no longer possible to perform the Zoom function. To use
the Zoom function again, it is necessary to erase the commands
programmed to those buttons. For details, see page 60.
Removing the batteries from the remote controller for at least 10 minutes
erases all of the commands that have been programmed in the remote
controller.
DV-S939(US_E)p56-60.p65 10/2/00, 3:26 PM59
59


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo dv s 939 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo dv s 939 in the language / languages: English as an attachment in your email.

The manual is 8,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info