63329
17
Zoom out
Zoom in
Previous page
1/32
Next page
17
Powering Up and Setting the Clock—
Continued
You can set the CR-L5 so that the time is displayed while
the CR-L5 is in Standby mode.
1
With the CR-L5 turned on, press and
hold the CR-L5’s [STANDBY/ON] but-
ton for more than 2 seconds.
To turn off the time display, repeat this procedure.
Notes:
Setting the CR-L5 to display the time will slightly
increase the power consumption in Standby mode.
You can display the day and time at anytime.
1
Press the [CLOCK CALL] button.
The day and time appear on the display.
Press the [DISPLAY] button to toggle between 12- and
24-hour formats.
Press the [CLOCK CALL] button again to return to the
previous display.
If the correct day and time appear on the display, you
can skip the following sections and go straight to page 19
for information on using and enjoying your CR-L5.
If “Adjust” appears on the display:
The clock has not been set for one of the following reasons:
The FM antenna is not connected properly or the signal is
too weak.
Check the antenna connection or install an outdoor FM
antenna (see page 15), and try setting again (see “Setting
ACCUCLOCK to Use a Specific Station” on this page).
The detected RDS station does not support CT (Clock
Time) information.
Some RDS stations don’t support CT. In this case you
should specify the station to be used (see “Setting
ACCUCLOCK to Use a Specific Station” on this page).
If the wrong day or time appears on the display:
If you live close to the border with another country, the CT
information may have been taken from a radio station in
another time zone. In this case you should specify another
station and try setting again (see “Setting ACCUCLOCK to
Use a Specific Station” on this page).
The ACCUCLOCK function normally uses the FM station
with the strongest signal to set the clock. If the clock cannot
be set properly using that station, you can specify which FM
station the ACCUCLOCK function should use. This must
be an FM station that supports RDS CT (Clock Time) infor-
mation.
1
Press the [TIMER] button.
“Clock” appears on the display.
If the clock has already been set, a timer option appears
instead. In this case, you’ll need to press the [TIMER]
button repeatedly until “Clock” appears.
2
Press the [ENTER] button.
AccuClock” appears on the display.
If “Manual Adj.” appears, use the Up/Down [ ]/[ ]
buttons to select “AccuClock”.
3
Press the [ENTER] button.
The display appears as shown (the frequency will be
different).
4
Use the [ ]/[ ] buttons to tune into
the FM station.
The RDS indicator appears when tuned into a station
that supports RDS, as shown.
If you’ve stored some radio presets, you can use the
PRESET [ ]/[ ] buttons to select the FM station.
5
Press the [ENTER] button.
While the clock is being set, “Wait” flashes on the dis-
play. It may take a few minutes to set the clock.
When the clock has been set, the message “Clock
Adjusted” scrolls across the display, then the day and
time are displayed for a while.
Notes:
If the clock has not been set correctly, specify another FM
station and try again, or set the clock manually (see
page 18).
If you don’t want the clock to be updated automatically,
you can turn off the ACCUCLOCK function (see page 16).
Displaying the Time in Standby
Mode
Displaying the Day & Time
Setting ACCUCLOCK to Use a
Specific Station
AC means ACCUCLOCK
RDS indicator
CR-L5_E.book Page 17 Monday, May 19, 2003 4:05 PM
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo CR-L5 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo CR-L5 in the language / languages: English as an attachment in your email.

The manual is 1,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo CR-L5

Onkyo CR-L5 User Manual - German, Dutch, Swedish - 96 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info