159239
39
Zoom out
Zoom in
Previous page
1/40
Next page
39
Troubleshooting—
Continued
Trouble Possible Cause Remedy
The timer didn’t work?
The CR-505DAB was already on at the
specified ON time.
Set the CR-505DAB to Standby (page 33).
The CR-505DAB must be in Standby mode,
otherwise the timed task will not work.
The -connected cassette tape deck or
MD recorder had not been in standby mode.
You must set the recording devices to standby
mode too.
The specified ON time coincided, or over-
lapped the ON time of another timer.
Check the timer settings and correct as neces-
sary (page 34).
The CR-505DAB is only connected digi-
tally to the MD recorder.
To make recordings with -connected MD
recorder, connect the recorder’s analog inputs
to the CR-505DAB’s analog outputs.
No sound is output when a
timed playback or record-
ing task starts?
While a timed recording task is in progress,
the output of the CR-505DAB is muted.
To hear what’s being recorded, press the
[MUTING] button to cancel the Mute func-
tion. Press it again to mute the CR-505DAB.
For timed playback, the volume is deter-
mined by the [VOLUME] control.
Set the volume to a suitable level (page 19).
doesn’t work.
There’s no RCA/phono analog audio con-
nection.
To use you must make an analog audio
connection (RCA/phono) between CR-
505DAB and your Onkyo components even if
they are connected digitally.
Standby indicator flashes.
The protection circuit may be activated.
Make sure not to short-circuit the positive and
negative speaker wires.
Abnormal Behavior
The CR-505DAB contains a microcomputer for signal processing and control functions. In very rare situations, severe
interference, noise from an external source, or static electricity may cause it to lockup. In the unlikely even that this should
happen, unplug the power cord from the wall outlet, wait at least five seconds, and then plug it back in again.
Restoring the Default Settings
To reset the CR-505DAB to its factory defaults, turn it off and unplug the power cord. Then press and hold the [STANDBY/
ON] button on the CR-505DAB, and plug in the power cord.
39


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo cr 505 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo cr 505 in the language / languages: English as an attachment in your email.

The manual is 1,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info