492685
27
Zoom out
Zoom in
Previous page
1/32
Next page
27
En
There’s no sound.
• Make sure that the Onkyo Dock is connected to the
integrated amplifier properly.
• Make sure that no video content is being played.
Reset the iPod.
Other
• When the Auto Standby (ASb) function is activated, the
power of the Onkyo Dock connected via u is
automatically turned off ( page 25).
Can’t control properly by using the remote
controller.
• Make sure that the u cable is connected to the
integrated amplifier correctly.
Check that each device is connected correctly and that
the RI MODE switch is set correctly ( page 17).
No sound is heard from a connected
component.
• Make sure the correct input source is selected
( page 23).
Make sure the analog audio cable is connected correctly
( page 14).
When the u interlock does not function
properly
• Check that each device is connected correctly and that
the RI MODE switch is set correctly
( pages 15
to 17).
• Check that the switch on the back of the integrated
amplifier is set to the correct setting.
• The settings are not enabled when the switch is changed
during the Standby mode.
To change a setting, be sure to turn on the unit prior to
making any changes.
The connecting method may vary depending on the
device that will be connected. Please refer to the u
connection section in the owner’s manual of the
connected device.
The sound from turntable is distorted.
If your turntable has a built-in phono preamp, connect to
other analog inputs such as LINE IN.
If your turntable does not have a built-in phono preamp,
connect a turntable to PHONO ( page 19).
Make sure that the ground wire is connected. Otherwise,
it may produce an audible hum and noise.
The remote controller doesn’t work
properly.
Make sure the batteries have been installed with the
correct polarity (+/–) ( page 7).
Replace both batteries with new ones. (Do not mix
different types of batteries or new and old batteries.)
The remote controller is too far away from the integrated
amplifier, or there’s an obstacle between them
( page 7).
The integrated amplifier’s remote control sensor is being
subjected to bright light (inverter-type fluorescent light
or sunlight).
The integrated amplifier is located behind the glass
doors of an audio rack or cabinet.
Onkyo Dock
External Components
Remote Controller
Onkyo is not responsible for damages (such as CD
rental fees) due to unsuccessful recordings caused by
the unit’s malfunction. Before you record important
data, make sure that the material will be recorded
correctly.
The integrated amplifier contains a microcomputer
for signal processing and control functions. In very
rare situations, severe interference, noise from an
external source, or static electricity may cause it to
lockup. In the unlikely event that this should happen,
unplug the power cord, wait at least 5 seconds, and
then plug it again.
Before disconnecting the power cord from the wall
outlet, set the integrated amplifier to Standby.
If during idling the cover is too hot to touch, then
ventilation needs to be improved.
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo A-9030 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo A-9030 in the language / languages: English as an attachment in your email.

The manual is 2,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo A-9030

Onkyo A-9030 User Manual - German, Dutch - 116 pages

Onkyo A-9030 User Manual - French - 60 pages

Onkyo A-9030 User Manual - Italian, Swedish - 116 pages

Onkyo A-9030 User Manual - Spanish - 60 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info