778489

OneConcept 10035712 Manual

21
Zoom out
Zoom in
Previous page
1/64
Next page
21
EN
INSTALLATION
1. Remove the appliance from the packaging and make sure that all accessories
(incl. ice basket and ice spoon) are included. Contact the costumer service if any
accessories are missing.
2. Make sure that the appliance is level and placed on a stable table or work surface
to avoid malfunctions.
3. The incline angle of the ice cube maker cabinet should not exceed 45° during
transportation or use. Do not turn the appliance upside down as this could damage
the compressor or the cooling system. After moving or transporting the appliance,
leave it unused for some time to allow the liquids in the compressor to settle. Wait at
least 2 hours before using the appliance for the rst time and after you have placed
it in the appropriate location and aligned it correctly.
4. Place the appliance in an adequately ventilated place on a dry and level surface.
Do not use the appliance near heat sources such as stoves, heaters or corrosive
gases. Keep a minimum distance of 20cm to all sides of the ice cube maker to
ensure proper ventilation.
5. Do not ll the water reservoir with hot water as this may damage the appliance. It is
best to ll the water reservoir with water that is at room temperature or cooler.
6. Do not use the appliance at a very cold environment (lower than 5 °C).
7. Clean the appliance before use (see section “Cleaning and Maintenance“).
COMMISSIONING AND OPERATION
1. Ensure that the drain plug at the bottom of water reservoir is closed well.
2. Plug the ice cube maker into the wall outlet, the ice making indicator lights
solidly.
Note: If the appliance has been moved, allow the ice cube maker to rest for
30minutes before plugging the power plug into the wall outlet.
3. Open the top lid and remove the ice basket.
4. Fill the water reservoir with drinking water.
Note: Do not ll above the MAX water level mark.
5. Replace the ice basket and close the top lid.
6. Press the ON/OFF button and the ice making indicator blinks.
7. The ice-making cycle will last approximately 7-15 minutes, depending on the
ambient temperature and water temperature.
8. The ice-making cycle starts with water being pumped into the ice tray situated
below the evaporator. Over the next 7-15 minutes ice forms on the evaporator.
Once this has completed, the ice tray will tilt backwards and the remaining water in
the ice tray is drained back into the water reservoir. The ice cubes are then dropped
from the evaporator and pushed forward into the ice basket by the ice shovel.
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for OneConcept 10035712 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of OneConcept 10035712 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 2.91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info