122778

One for All urc 7556 digital 5 Manual

21
Zoom out
Zoom in
Previous page
1/450
Next page
WWW.ONEFORALL.COM 19
Your ONE FOR ALL 5 Remote Control is compatible with ONE FOR ALL Light
C
ontrol accessories, allowing you to control one or more of the lights in your
h
ouse using the remote. To begin, you will need to purchase the ONE FOR ALL
Light Control Starters Kit (HC-8300). The next step is to set up a code on a spare
device key, which will allow you to control up to 10 Light Control Receivers. The
code should be set up on a key which is configured to accept a AMP code. If you
a
re already using the AMP key, you will need to change a spare device key to
accept a AMP code. To do this, follow the Mode Re-Assignment feature on page
12.
T
o set-up a code, simply follow the normal procedure on page 6. The following
codes can be set up for Light Control:
OFA Light Control – 1000, 1001, 1002, 1003, 1004, 1005, 1006, 1007, 1008,
1
009, 1010, 1011, 1012, 1013, 1014, 1015
I
t is recommended to use the first code listed. As the Light Control system works
with Radio Frequency there is the possibility of interference. If your Light
Control kit is not responding well, try one of the other codes listed.
Set up the HC Receiver
To set up your HC Receiver to work with your remote, you will need to
assign a number to it. This is a one-time process that will allow you to
control individual lights separately if you purchase additional HC Receivers
in the future. To assign a number to the plug, follow these steps:
• Plug the lamp into the HC Receiver, and plug the HC Receiver into the
wall outlet. If your lamp has a power switch it should be in the “ON”
position.
• Plug the Command Centre in as close as possible to the HC Receiver, so
that they are only 10-20 cm apart (the Command Centre can be
moved after the initial setup).
• Press the Light Device key on your remote control so that it is in Light
Mode.
• Press the number you wish to assign to the HC Receiver. If this is your
first Plug, number 1 is recommended, number 2 for the second etc.
The LED (underneath the Light Device key) should blink twice.
• Press and hold the button on the HC Receiver until the red light
begins to blink.
• Point your remote control towards the Command Centre and press the
Channel Up (+) key. The red light should stop flashing.
The remote should now operate the HC Receiver. To test it, check if the
Channel Up (+) and Channel Down (-) keys work to turn
your light on and off respectively, or if you have the HC8010 Dimmer
unit, see if the Volume up key begins to brighten or darken the light
(press again to stop).
Extra Features
ONE FOR ALL Light Control
1
2
3
706153_URC7556_EURO_10t:Ofa5_Digital_URC7555_EURO_10_Talen 04-12-2007 17:03 Pagina 19
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for One for All urc 7556 digital 5 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of One for All urc 7556 digital 5 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info