492752
2
Zoom out
Zoom in
Previous page
1/4
Next page
Step 1:
Installing the Batteries
Step 3:
Setting Up Your Devices
1
1
2
Match the batteries to the + and - marks inside
the battery case, then insert the batteries.
3
Press the battery cover back into place.
1st TV code
2nd TV code
3rd TV code
1st VCR code
2nd VCR code
3rd VCR code
1st Cable code
2nd Cable code
3rd Cable Code
Step 2:
Looking Up Your Electronic Device Code
You will need one of these codes to program your One For All
®
Easy 3 Device remote.
Look at your Electronic Device to find out the brand name and
write it in the space below:
TV ________________________
VCR _______________________
Cable _______________________
1
2
Your One For All
®
Easy 3 Device needs two (2) new AAA
alkaline batteries. To install the batteries:
On the back of the
One For All
®
Easy 3
Device, push down on the tab and lift the
cover off.
Set-Up Codes
RCA 1213
Sony 1111
Turn on your TV, VCR or Cable Box, depending on the
device you are programming.
2
Press TV* and release. Press and hold SETUP
until the One For All
®
Easy 3 Device's red
light blinks twice. Release SETUP.
* Note: When setting up your VCR and/or Cable Box,
substitute the appropriate device key (VCR or CBL).
3
Using the example
shown on the
right, enter the
first four-digit
code you wrote
down for the
device you are
setting up. (See
"Looking Up Your
Electronic Device
Code".) If you put
in the code
correctly, the red
light will blink
twice.
TV
4
Test the unit by pressing POWER. The red
light (LED) should blink once.
POWER
Note: Removing the batteries for more than 30 minutes will require you to
reprogram the remote control.
SETUP
+
Find your Device brand in the listing on the re-
verse side of these instructions. The most
popular codes are listed first. Write your codes
here:
How to Enter Codes
If your TV
Press
code is:
1
VOL
1
2
VOL
2
CH
+
3
3
CH
-
4
4
TV Set Up
Aim the One For All
®
Easy3 Device at your TV
and press POWER. Your TV should turn off. If it
doesn't, repeat Steps 2-4, trying each code listed for
your brand until you find the one that operates your
TV.
VCR Set Up
Aim the One For All
®
Easy3 Device at your
VCR and press POWER. Your VCR should turn
off. If it doesn't, repeat Steps 2-4, trying each code
listed for your brand until you find the one that
operates your VCR. If your original VCR remote
did not have a POWER key, put a tape in your
VCR and press PLAY on the One For All
®
Easy3
Device.
Cable Set Up
Aim the One For All
®
So Easy 3 Device at your
Cable Box and press POWER. Your Cable Box
should turn off. If it doesn't, repeat Steps 2-4, trying
each code listed for your brand until you find the
one that operates your Cable Box. If your original
Cable Box remote did not have a "ON" key, Use
CH + on the One For All
®
Easy 3 Device to
turn your Cable Box on.
4
POWER
POWER
or
POWER
CH
+
3
or
PLAY
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for One for All URC 3034 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of One for All URC 3034 in the language / languages: English as an attachment in your email.

The manual is 0,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info