651593
5
Zoom out
Zoom in
Previous page
1/12
Next page
Instructions for Machine Transport
NOTE: Refrigerated equipment must remain upright to avoid damage to the compressor.
In order to prevent the oil contained in the compressor from flowing into the cooling system, it is
necessary to always ship, carry, store and handle this drink dispenser in an upright position, fol-
lowing the instructions located on the packaging. Never ship, carry, store or handle this unit on
its side.
1.1 RECEIVING
Each unit is completely tested under operating conditions and thoroughly inspected before
shipment. At the time of shipment, the carrier is responsible for the unit and any claim for dam-
age must be made with the carrier. Upon receiving units from the delivering carrier, carefully in-
spect the carton for visible indication(s) of damage. If damage exists, have carrier note same
on bill of lading and file a claim with the carrier.
1.2 UNPACKING
A. Cut band and remove.
B. Carefully remove top portion of carton by lifting up, see figure 1.
C. Remove top inner carton pad from inside of packing box.
D. Inspect unit for concealed damage and if evident, notify delivering carrier and file
a claim against same.
Installation Positioning the machine
The machine must be well ventilated. Leave an 8” (20 cm) clearance on the sides and back of
the machine to allow proper ventilation. Installation of the machine near a heat source
should be avoided. Some heat sources you should avoid locating this unit too close to are
ovens, coffee machines, cold or frozen beverage dispensers or ice machines (equipment with
compressors that expel hot air through its vents). A room temperature between 5F (15°C)
and 7F (25°C) is recommended.
Connection to Main Power Supply
• The electrical safety of this drink dispenser can only be achieved if the machine is properly
connected to an appropriate grounded receptacle that is in compliance with current national
safety standards. Therefore, the manufacturer cannot be held responsible for damage and/or
injury caused by failure to connect the unit to an appropriate source of power.
• For a safe and correct installation, connect the unit to a dedicated outlet.
• Do not alter the cord or plug in any way.
• The entire length of the power supply cord must not, in any way, be compressed, bent, or
bunched together, nor may extension cords be used.
• Do not obstruct the ventilation vents on the side and rear panels of the unit. Insufficient venti-
lation will reduce the efficiency of the machine, causing it to function inadequately, and can
cause serious damage. A minimum of eight inches (20cm) clearance is necessary on each side
and behind the unit.
WARNING: THIS UNIT MUST BE PROPERLY ELECTRICALLY GROUNDED TO AVOID POSSIBLE FATAL
ELECTRICAL SHOCK OR SERIOUS INJURY TO THE OPERATOR. THE POWER CORD IS PROVIDED WITH
A THREE PRONG GROUNDED PLUG. IF A THREE-HOLE GROUNDED ELECTRICAL OUTLET IS NOT
AVAILABLE, USE AN APPROVED METHOD TO GROUND THE UNIT. DO NOT USE EXTENSION CORDS
WITH THIS UNIT. DO NOT GANG TOGETHER WITH OTHER ELECTRICAL DEVICES ON THE
SAME OUTLET.
4
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Omega OSD30 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Omega OSD30 in the language / languages: English as an attachment in your email.

The manual is 3,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info