61296
4
Zoom out
Zoom in
Previous page
1/14
Next page
Power Supply
Standby Mode and Display Shut Off
If the recorder is stopped for 5 minutes or longer during recording or playing, it goes
into Standby (power-save) mode, and the display shuts off. To exit Standby mode and
turn on the display, press any button.
1
Press and hold the
2
(MENU) for 1 second or
longer to go to the mainmenu.
2
Press the 9 or 0 to select the “Sub
Menu”, and press
t
.
“Time & Date” is displayed, and flashes.
3
Press the 9 or 0 button to select the item
to set.
Select the item from “year”, “month”, “day”, “hour”
and “minute” with a flashing point.
4
Press the + or
button to set.
Follow the same steps by pressing the 9 or 0
button to elect the next item, and press the
+
or
button to set.
5
Press the
t
button to complete the setup
screen.
The clock will start from the set date and time.
Press the
t
button according to the time signal.
6
Press the 5 button to close the menu mode.
This completes the time/date setup procedure.
s You can choose between 12 and 24 hour display by pressing the
2
(DISP.) button
while setting the hour and minute.
s You can change the order of the date indication by pressing the
2
(DISP.) button
while you are setting the year, month, or day.
s If you leave the battery compartment disconnected from the recorder for a longer
period of time or if you remove the battery compartment repeatedly at short intervals,
you may have to reset the time.
(Example: June 14, 2007)
Hold
Setting the HOLD switch to the direction of the arrow holds the current status, and all
button operations are disabled. This feature is useful when the recorder is carried in a
handbag or pocket. Remember to release the HOLD switch to use the recorder.
Notes
s Setting the HOLD switch to the direction of the arrow during playback will turn off the
display at the time when playback of the current file ends.
s Setting the HOLD switch to the direction of the arrow during recording will turn off the
display and finish recording at the time when the remaining recording time reaches to
zero.
-
4
-
Setting Time/Date (Time & Date)
If you have set the time and date, information as to when a sound file was recorded is
stored automatically with that file.
When using the recorder for the first time, or after the battery has been taken out for
a log period of time, the “year” indication will flash. In such a case, be sure to set the
time and date by following steps 4 through 6 described below.
Power ON
Power OFF
Slide the HOLD switch in the direction opposite that
indicated by the arrow.
The display will turn on and the power will be turned on.
The resume function will bring the recorder back to the stop
position in memory before power was turned off.
Slide the HOLD switch in the direction indicated by the
arrow while the recorder is not in operation.
The display shuts off and the power will be turned off.
The resume function remembers the stop position before the
power is turned off.
HOLD
HOLD switch
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Olympus WS-110 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Olympus WS-110 in the language / languages: English as an attachment in your email.

The manual is 0,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info