2422
6
Zoom out
Zoom in
Previous page
1/65
Next page
11
ENEN
10
SPECIAL FEATURES
Press the selftimer/remote control
button. The mode switches in the order
shown on the left. The selected mode
is displayed on the LCD Panel.
Press the mid-roll rewind button with the
protrusion on the strap buckle 1. Do not
use an instrument with a sharp tip.
Unload the film as described on page 7.
OTHER OPERATIONS
First select the date/time mode you
want to print. Press the MODE
button. Each time you press it, the
mode will switch in the order shown
on the left. Keep the mode you want
to print displayed. Date/time is
imprinted in the lower right corner of
the picture. If the date/time is
superimposed on a bright color like
white, orange, yellow, etc., it may be
difficult to read. When black-and-
white film is used, the date/time may
not be printed.
None
Year-month-day
Month-day-year
Day-month-year
Day-hour-minute
CORRECTING THE DATE AND TIME
(Quartzdate model only)
Be sure to correct the date and time after the battery has been inserted or
replaced.
1. Keep the MODE button pressed until the “year” indicator starts blinking.
2. Press the SET button to adjust the “year” indicator. If you press the
button once, the number on the display will advance by 1. If you keep
the button pressed, the numbers will run in rapid succession. If you
pass the intended number, keep pressing to return to that number.
3. Press the MODE button once more to make the “month” indicator blink.
Press the SET button to adjust the “month” indicator. As you press the
MODE button, the blinking indicator changes in the order of “year”,
“month”, “day”, “hour” and “minute”.
4. Repeat Steps 2 and 3 to set “hour” and “minute”. Make sure the
“minute” indicator is blinking.
5. When “minute” has been set, press the MODE button. None of the
indicators will be blinking and date/time correction is now complete.
REPLACING THE REMOTE CONTROL BATTERY
(Optional RC-300C)
If the selftimer/remote control indicator doesn’t blink even when you
press the button, replace the battery with a new one (CR2025).
1. Turn the screw on the bottom of the remote control counterclockwise to
loosen.
2. Turn the remote control over, and remove the cover. With the battery
facing up, remove the old battery and insert a new battery as shown.
3. Replace the cover, turn the remote control over, and turn the screw on
the bottom clockwise to tighten (see figure 9 on page 127).
1
SETTING THE SELFTIMER/REMOTE CONTROL
Selftimer
Secure the camera on a tripod or other support. Compose your shot in the
viewfinder. Press the shutter release button halfway (the focus and
exposure are locked at this time). Then press the shutter release button all
the way. The selftimer indicator lights for about 10 seconds and then blinks
for about 2 seconds. After this, the shutter will release.
Remote Control RC-300C (Optional)
Compose your shot in the viewfinder. Position the autofocus frame on your
subject. To take a picture, point the remote control at the camera and
press the button on the remote control. The selftimer/remote control
indicator starts blinking, and the shutter will release about 3 seconds later
(see figure 8 on page 127).
Camera Shake Indicator
In this mode, the camera warns you before you shoot if camera shake is
likely to cause blurring. Also, when there is significant camera shake, this
mode helps reduce blurring. If the green and orange lamps blink
alternately when you hold the camera, it means that the camera is shaking
and blurring may result. Hold the camera securely until the lamps stop
blinking; then press the shutter release button.
OTHER OPERATIONS
REWINDING THE FILM MID-ROLL
Mode display
Mode
—————
Selftimer
Remote Control
Camera Shake
Indicator
No
display
PRINTING THE DATE/TIME (Quartzdate model only)
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Olympus mjuIII 150 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Olympus mjuIII 150 in the language / languages: Dutch as an attachment in your email.

The manual is 5,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info