589209
47
Zoom out
Zoom in
Previous page
1/53
Next page
46 47
CUSTOM SETUP
Custom setup allows each user to customize flash setup to suit his or her preferences.
Setup procedure
1. Tu rn the Macro Flash Controller on.
2. Press and hold the MODE button for more than 2 sec-
onds, until the setup mode display appears in the control
panel.
3. Tu rn dial A to select the setup mode.
4. Tu rn dial B to select the value.
5. Press the MODE button to exit from setup and return to
the previous control panel display.
Setup mode
Mode display
Dial A
Value display
Dial B
Function Default
AF illuminator
lamp
LAMP timer
Light intensity
adjustment
Guide number
display
Guide number
Unit of distance
AF illuminator is activated according to the control
from the camera.
AF illuminator is defeated.
The lighting time of the modeling lamp can be set.
Selectable time: 1" (1 sec.) ~ 10", 15", 20", 25", 30",
40", 50", 60" and – –" (3 min.)
Light intensity cannot be adjusted.
Light intensity can be adjusted.
The light intensity in MANUAL mode is displayed in
terms of light intensity ratio.
The light intensity in MANUAL mode is displayed in
terms of guide number.
Guide numbers are displayed in meters.
Guide numbers are displayed in feet.
A
30"
OFF
OFF
m
ALL RESET
All Reset resets the custom setups to the factory default settings.
Press the MODE and LIGHT buttons simultaneously for 2 or
more seconds to reset the custom setups (except for the
distance display unit (m/ft)) to the default settings.
The distance display unit (m/ft) is not altered by the all reset
operation.
Restore the Ring Flash (RING) and Twin Flash (TWIN) modes
respectively.
WARNING DISPLAY LIST
Warning details Control panel display Remedy
The Ring Flash or Twin Flash
is not connected.
The Twin Flash light ratio is
improper.
Flash emission with the se-
lected light ratio is not pos-
sible in Manual mode.
The display disappears automatically in
about 4 seconds. When the display has dis-
appeared, connect the Ring Flash or Twin
Flash.
The display disappears automatically in
about 4 seconds.
• When the display has disappeared, re-con-
nect the Ring Flash or Twin Flash.
∼ 
•Set the proper Twin Flash light ratio or light
intensity ratio.
MACRO FLASH CONTROLLER
FC-1
MODE
LAMP
AUTO
CHECK
TEST/
CHARGE
POWER
LIGHT
RATIO GN/
MACRO FLASH CONTROLLER
FC-1
MODE
LAMP
AUTO
CHECK
TEST/
CHARGE
POWER
LIGHT
RATIO GN/
Connection failure during or
connector disconnection dur-
ing power ON.
Custom setup can be performed separately for the Ring Flash (RING) and Twin Flash (TWIN).
47


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Olympus FC-1 Macro Flash System at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Olympus FC-1 Macro Flash System in the language / languages: English as an attachment in your email.

The manual is 4,51 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info