589209

Olympus FC-1 Macro Flash System Manual

15
Zoom out
Zoom in
Previous page
1/53
Next page
14 15
<Attaching to the camera/Removing from the camera>
Confirm that both the camera and Macro Flash Controller are off.
Attaching or removing the Macro Flash Controller while either it or the camera is on may result in
malfunction.
How to attach
1. Place the head section in the standard position (horizon-
tal, front).
2. Remove the hot shoe cover from the camera.
• Store the hot shoe cover in the pocket of the macro flash
case to avoid losing it.
3. Loosen the lock ring.
• If the lock pin is in the out position, put it to the in position by
turning it all the way in the opposite direction to [←LOCK]
until it stops.
• Do not apply excessive force to the lock pin.
• Do not touch the electric contact with a finger or metallic object.
• Do not attach the Macro Flash Controller while the lock pin is in the out
position. Otherwise, malfunction may result.
4. Slide the Macro Flash Controller all the way into the hot
shoe until it clicks and stops.
5. Tu rn the lock ring all the way in the direction of [←LOCK]
until it stops.
How to remove
1. Loosen the lock ring, then slide the Macro Flash Control-
ler out of the hot shoe.
2. Attach the hot shoe cover to the camera.
Lock pin
Electric contact
Attach the RF-11 Ring Flash or TF-22 Twin Flash to the Macro Flash Controller.
• How to use the RF-11 Ring Flash : See page 15.
• How to use the TF-22 Twin Flash : See page 27.
RING FLASH RF-11
1. While aligning the indices, attach the RF-11 Ring Flash to
the lens.
2. Press the Ring Flash release button of the FC-1 Macro
Flash Controller to remove the cap.
3. IInsert the RF-11 Ring Flash connector terminal into the
Ring Flash connector on the FC-1 Macro Flash Controller
until it clicks.
• When unplugging the connector, be sure to press and hold
the Ring Flash release button. Be sure to attach the cap
after unplugging the connector.
• Do not pull the cord when plugging or unplugging the con-
nector. Always grasp it by the connector plug. Pulling the
cord could damage the connector wire.
<Attaching to the camera>
• Attach the FC-1 Macro Flash Controller to the camera beforehand.
• To prevent the Ring Flash from falling off, attach it with the camera in a stable position.
Notes
• Confirm that both the Macro Flash Controller and Ring Flash are off before attaching or removing them. Otherwise,
malfunction may result.
• Be sure to leave the Twin Flash connectors capped. Otherwise, the Macro Flash Controller cannot be turned on.
Memo
The Ring Flash and Twin Flash connector terminals are subject to high voltages. To ensure safety, the Macro Flash
Controller is designed so that it cannot be turned on unless one of the flashes is connected to it and all of its unused
connectors are capped.
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Olympus FC-1 Macro Flash System at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Olympus FC-1 Macro Flash System in the language / languages: English as an attachment in your email.

The manual is 4,51 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info