509044
110
Zoom out
Zoom in
Previous page
1/133
Next page
110
EN
Information
10
3
Adjust the settings for each group in the super control panel.
Flash intensity
value
250250 F5.6
0.0
0.0
P
3838
A Mode
TTL
M
Off
+5.0
TTL +3.0
1/8
LO
1
Ch
Group
• Select the ash control
mode and adjust the ash
intensity separately for
each group. For MANUAL,
select the ash intensity.
Normal ash/Super FP ash
• Switch between normal
ash and Super FP ash.
Communication light level
• Set the communication
light level to [HI], [MID],
or [LO].
Channel
• Set the communication
channel to the same
channel used on the ash.
Flash
intensity
Flash control
mode
Adjust settings for the
camera ash unit.
4
Attach the supplied ash unit and raise the ash head.
• After con rming that the built-in and remote ash units have charged, take a test shot.
Wireless ash control range
Position the wireless ash units with their remote sensors facing the camera. The following
illustration shows the approximate ranges at which the ash units can be positioned. The
actual control range varies with local conditions.
7m
5m
100°100°
50°
50°
50°
50°
60°
60°
30°
30°
30°
30°
# Cautions
We recommend using a single group of up to three remote ash units.
• Remote ash units cannot be used for second curtain slow synchronization or anti-shock
exposures longer than 4 seconds.
If the subject is too close to the camera, the control ashes emitted by the supplied ash
may affect exposure (this effect can be reduced by reducing the output of the supplied
ash by, for example, using a diffuser).
The upper limit of ash synchronization timing is 1/160 sec. when using the ash in
remote control mode.
Other external ash units
Note the following when using a third-party ash unit mounted on the camera hot shoe:
• Using obsolete ash units that apply currents of more than about 24 V to the camera hot
shoe X-contact will damage the camera.
• Connecting ash units with signal contacts that do not conform to Olympus speci cations
may damage the camera.
Use only with the camera in shooting mode M at shutter speeds slower than 1/160 s and
at ISO settings other than [Auto].
Flash control can only be performed by manually setting the ash to the ISO sensitivity
and aperture values selected with the camera. Flash brightness can be adjusted by
adjusting either ISO sensitivity or aperture.
• Use a ash with an angle of illumination suited to the lens. Angle of illumination is usually
expressed using 35-mm format equivalent focal lengths.
110


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Olympus E-PL5 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Olympus E-PL5 in the language / languages: English as an attachment in your email.

The manual is 3,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Olympus E-PL5

Olympus E-PL5 User Manual - German - 132 pages

Olympus E-PL5 User Manual - Dutch - 132 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info