569117
19
Zoom out
Zoom in
Previous page
1/75
Next page
37
7 Cleaning & Maintenance
7.1 Cleaning the exterior of the device
Attention: Before cleaning the device with a damp cloth, disconnect
the power plug!
Clean the housing using a cloth moistened with clean water with a little mild
soap applied.
Note: Never use solvents or aggressive cleaning agents.
7.2 Cleaning the transport rollers
Deposits and residual adhesive on the transport rollers can influence the
results of the laminating process. Therefore, clean the transport rollers at
regular intervals:
1. Set the function switch to 100/125 mic.
2. Wait until the READY indicator lights up continuously.
3. Insert a piece of folded paper in the laminator infeed.
4. Repeat the process with a new piece of paper until there are no more
deposits or residual adhesive to be seen on the paper.
'HSRVLWVDQGUHVLGXDODGKHVLYHRQWKHWUDQVSRUWUROOHUVFDQLQÀXHQFHWKH
UHVXOWVRIWKHODPLQDWLQJSURFHVV7KHUHIRUHWKHWUDQVSRUWUROOHUVPXVWEH
FOHDQHGSHULRGLFDOO\DIWHUXVH
7RGRWKLVLQVHUWDIROGHGSLHFHRISDSHULQWKHLQVHUWLRQVORW5HVLGXDO
DGKHVLYHLVUHPRYHGDQGWDNHQXSE\WKHSDSHUZKHQHMHFWHG5HSHDWWKH
SURFHVVVHYHUDOWLPHV
'LVFRQQHFWWKHSRZHUSOXJEHIRUHVWDUWLQJWRFOHDQWKHXQLWZLWKDGDPS
FORWK,IQHFHVVDU\WKHKRXVLQJFDQEHFOHDQHGXVLQJDFORWKPRLVWHQHG
ZLWKFOHDQZDWHUZLWKDOLWWOHPLOGVRDSDSSOLHG1HYHUXVHDQ\VROYHQWVRU
DJJUHVVLYHFOHDQLQJDJHQWV

38
8 Troubleshooting
Problem Diagnosis & Cause Solution
The power plug is not
plugged into the power
socket properly.
Connect the power plug in
the power socket properly.
The On/Off witch is set to
OFF.
Set the On/Off switch to ON.
POWER indicator
does not light up
The POWER indicator is
defective.
Contact our Hotline.
Laminated foil is
not completely
transparent
The laminating temperature
was too low.
Ensure that you allow the
device sufficient time to heat
up when using thicker
lamination foil.
Laminate the same foil again
to improve the lamination
result.
The lamination foil was
inserted askew in the
laminator infeed.
Foil jam
The lamination foil is too
large.
Refer to Chapter "Clearing
jammed lamination foil".
Refer to Chapter “Cleaning
the transport rollers”.
Insert the lamination foil in
the laminator infeed straight
and with the closed side first.
Only use lamination foil of the
specified sizes, refer to
Chapter "Technical Data".
The device no
longer works after
a longer period in
operation or stops
during operation
Is the surface of the device
hot? If so, the device's
overheating protection has
probably switched the
laminator off automatically.
Wait for approx. 30 minutes
and try to laminate again. If
the device does not work,
contact our Hotline.
The transport
rollers do not run
Is the power plug connected
to the power socket?
Is the On/Off switch is set to
ON?
If the problem continues,
contact our Hotline.
If the problem cannot be solved, contact our Hotline; refer to Chapter
“Guarantee”.
38
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Olympia A 240 Combo at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Olympia A 240 Combo in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 6,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info