Manual Olsberg Pico Compact (page 15 of 56) (English, German, Dutch, French, Spanish)

707633

Zoom out

Zoom in

1/56

Chimney design

The chimney design is according to DIN EN 13384 -1

and 2 or to the specic national regulations. The chim-

ney must comply with the temperature class T400.

Necessary data

Closed operation

with billet wood / wood briquettes / lignite briquettes:

● Nominal thermal output ................. 5,0 / 5,0 / 5,0 kW

● Waste air mass ow rate ............... 4,0 / 4,1 / 4,7 g/s

● Waste air temperature at

connection duct ........................... 340 / 324 / 351 °C

● Minimum delivery pressure at

nominal thermal output ...................... 12 / 12 / 12 Pa

Combustion air supply

The Pico Compact stove can be operated convention-

ally, dependent on the ambient air as well as independ-

ent of the ambient air.

It must be guaranteed that there is enough combustion

air available for the stove. For the proper function of the

stove, a necessary combustion air volume current of

15,6 m³/h must be considered.

Ambient air independent

combustion air connection

By an ambient air independent operating mode, the

combustion air must be added from outside through a

leak-proof line or through a supply duct in the chimney.

Thus, speak with your district chimney sweep master.

Due to energy saving reasons, the combustion air in-

let should be able to be blocked if the stove is not being

operated. This can occur through a shut-off valve in the

combustion air line or through the air slide valves on

the stove. If a shut-off valve is used, this must be clear-

ly identied with CLOSED/OPEN.

Through the shutoff, it is avoided that heat is removed

from the set-up room through the constant circulation

of cold combustion air and cold combustion air lines

may lead to an increased formation of condensation.

Attention:

The combustion air line may not be closed during

operation!

In order to feed the combustion air to the stove exter-

nally via a pipe instead of from the room in which it is

installed, it is possible to screw a Ø 125 mm combus-

tion air pipe to the back of the stove or at the bottom.

If attaching the combustion air line at the rear of the ap-

pliance, remove the cover seated on the rear base pan-

el and screw in the included connection duct through

the hole in the rear base panel tted on the appliance.

f the combustion air is supposed to be supplied from

the bottom, remove the cover seated on the rear base

panel and use the cover to seal the opening in the ap-

pliance through the hole in the rear base panel. The

combustion air line routed up from the bottom ends

ush with the oor on which the appliance is installed.

A ange with a sealing lip that provides for an airtight

connection between the appliance and the oor on

which it is installed has been included with the appli-

ance to t this type of installation scenario. Refer to

Fig.3 to Fig.6 for the position of the combustion air line.

When installing the ange, make sure the sealing lip,

which is approx. 20mm in height, faces down towards

the oor on which the appliance is installed (see Fig.1).

If opting for a distance greater than the minimum dis-

tance to the mounting wall, you need to adjust the posi-

tion of the combustion air line accordingly.

If the combustion air pipe installed is longer than 3 m,

calculations will have to be carried out to verify an ad-

equate supply of combustion air. At extremely low out-

door temperatures, condensation can occur on the

combustion air duct. For this reason it must be insulat-

ed with a suitable insulating material. Observe the rules

of the oven and air heating construction craft.

Use the Olsberg combustion air pipes with sealing lip.

Fig.1 Sealing lip

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Olsberg Pico Compact in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 4,26 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Olsberg Pico Compact Manual

Product: