Manual Oleo-Mac GS35C (page 12 of 60) (English, German, French, Italian, Spanish)

644160

Zoom out

Zoom in

1/60

1234

Italiano English Français

MONTAGGIO BARRA E CATENA FITTING THE BAR AND CHAIN MONTAGE GUIDE ET CHAINE

- Tirare la protezione (Fig. 1) verso l’impugnatura anteriore

per verificare che il freno catena non sia inserito.

- Togliere i dadi (A) e smontare il carter copricatena

(B, Fig. 2).

- Eliminare lo spessore in plastica inserito sui prigionieri

barra (C, Fig. 3).

- Portare il nottolino tendicatena (D) tutto verso il rocchetto

(E) (Fig. 3) agendo sulla vite tendicatena (L, Fig. 5).

- Inserire la barra (F, Fig. 3) sui prigionieri in modo che il

nottolino tendicatena (D) entri nell’apposito alloggiamento

(G).

- Montare la catena (H, Fig. 4) dentro al rocchetto (E) ed alla

guida della barra (M). Fare attenzione al senso di rotazione

della catena (Fig. 6).

- Montare il carter copricatena ed i relativi dadi senza

serrarli.

- Tendere la catena per mezzo della vite tendicatena

(L, Fig. 5).

- Serrare definitivamente i dadi di fissaggio del carter

copricatena tenendo sollevata la punta della barra (Fig. 7).

La coppia di serraggio è di 1,5 kgm (15 Nm). La catena

deve essere regolata in modo che sia ben tesa e possa

scorrere facilmente con la forza della mano (Fig. 8).

- La catena è regolata alla giusta tensione quando la si

può sollevare di qualche millimetro tirandola verso l’alto

(Fig. 8).

ATTENZIONE - Controllare più volte la tensione della

catena durante l’uso giornaliero della motosega.

Utilizzare sempre guanti protettivi.

- Pull the guard (Fig. 1) towards the front handle to check

that the chain brake is not on.

- Remove the bar nuts (A) and the chain cover (B, Fig. 2).

- Remove and discard the plastic shim from the bar studs

(C, Fig. 3).

- Bring the chain tensioning pin (D) fully towards the

sprocket (E) (Fig. 3) using the chain tensioning screw

(L, Fig. 5).

- Place the bar (F, Fig. 3) onto the studs so that the chain

tensioning pin (D) fits into its seat (G).

- Fit the chain (H, Fig. 4) inside the sprocket (E) and the bar

groove (M). Pay attention to the direction of rotation of the

chain (Fig. 6).

- Fit the chain cover and the relative nuts without tightening

them.

- Tension the chain by means of the tensioning screw

(L, Fig. 5).

- Hold the tip of the guide bar up and tighten the chain

cover nuts securely (Fig. 7). The tightening torque is 1,5

kgm (15 Nm). The chain should be taut but turn freely by

hand (Fig. 8).

- The chain is tensioned correctly when it can be pulled

upwards a few millimetres (Fig. 8).

WARNING - Check the chain tension frequently when

operating the chainsaw. Always use protective

gloves.

- Tirez la protection (Fig.1) en direction de la poignée

antérieure pour vérifier que le frein de chaîne n’est pas

enclenché.

- Otez les écrous (A) et démontez le carter de chaîne

(B, Fig.2).

- Eliminez l’épaisseur en plastique calée sur les prisonniers

du guide (C, Fig.3).

- Amenez le cliquet tendeur de chaîne (D) complètement

vers le pignon (E) (Fig. 3) par l’intermédiaire de la vis de

tension de la chaîne (L, Fig. 5).

- Placez le guide (F, Fig. 3) sur les prisonniers de manière que

le cliquet tendeur de chaîne (D) entre dans l’emplacement

prévu à cet effet (G).

- Montez la chaîne (H, Fig. 4) dans le pignon (E) et à la

rainure du guide (M). Faites attention au sens de rotation

de la chaîne (Fig. 6).

- Montez le carter protège-chaîne et les écrous

correspondants sans les serrer.

- Tendez la chaîne à l’aide de la vis de tension de la chaîne

(L, Fig.5).

- Serrez définitivement les écrous de fixation du carter

protège-chaîne en soulevant la pointe de guide (Fig.7).

Le couple de serrage de 1,5 kgm (15 Nm). La chaîne doit

être réglée, c’est à dire bien tendue et à même de glisser

facilement sous la pression de la main (Fig.8).

- La chaîne est correctement tendue lorsque vous pouvez la

soulever de quelques millimètres (Fig. 8).

ATTENTION - Contrôlez souvent la tension de la

chaîne pendant l’utilisation de la tronçonneuse.

Utilisez toujours des gants de protection.

was the mtd 140s a copy of this chainsaw I am trying to find a chain adjuster for my 140 S Submitted on 10-6-2020 at 09:08
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Oleo-Mac GS35C in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 1,55 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Oleo-Mac GS35C

Oleo-Mac GS35C User Manual - Dutch, Swedish, Norwegian - 60 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Oleo-Mac GS35C Manual

Product: