492989
21
Zoom out
Zoom in
Previous page
1/203
Next page
Installing Your Machine
-21-
Setup
1
The <
POWER SAVE
> key lights up while in the mode.
Memo
By factory default, the time interval to enter the power
saving mode is set to 1 minute. You can change the time
interval by pressing the <SETTING> key on the operator
panel and selecting [Admin Setup] > [Management] >
[Power Save] > [Power Save Time].
Sleep Mode
Your machine goes from the power saving mode
into the sleep mode after a set period of time. In
the sleep mode, the status of your machine is
almost the same as when it is turned off.
The <POWER SAVE> key blinks while in the
sleep mode.
The machine does not enter the sleep mode if an error
occurs.
If time-set transmission is scheduled, the machine will not
go into sleep mode.
If the fax transmission is waiting for a redial, the machine
cannot enter sleep mode.
When the network connection is switched from wired to
wireless, sleep mode is disabled. To enable sleep mode for
devices connected using wireless LAN, enable sleep mode
from the sleep mode setting menu. (MB451w and MB471w
only)
When a device using the wireless LAN connection goes into
sleep mode, the wireless LAN connection is broken. To
reconnect to the wireless LAN, press the power save key
on the device to recover from sleep mode. (MB451w and
MB471w only)
After the device connected to the wireless LAN has
recovered from sleep mode, it automatically connects to
the wireless access point using the same settings as before
it went into sleep mode. However, it may take up to 1
minute to connect. (MB451w and MB471w only)
When the network connection is switched from wireless
LAN to wired LAN, sleep mode is enabled. (MB451w and
MB471w only)
Memo
By factory default, the time interval to enter the sleep
mode is set to 30 minutes. You can change the time
interval by pressing the <SETTING> key on the operator
panel and then selecting [Admin Setup] >
[Management] > [Power Save] > [Sleep Time].
Returning to the Standby Mode
To return the machine to the standby mode from
the power saving or sleep modes, press the
<POWER SAVE> key on the operator panel.
Memo
When your machine receives a print job from a computer
or other devices, it automatically returns to the standby
mode.
Auto Power Off
When your machine is not used for a certain
period of time, the power turns off automatically.
Once the machine turns off, you need to turn on
to use it.
The machine has three settings to select the
machine's behavior on Auto Power Off.
Enable
Auto Config
Disable
Enable
When your machine is not used for a certain
period of time, it turns off the power
automatically.
Auto Config
The machine will not turn off automatically under
the conditions listed below.
- An Ethernet cable is attached to network
interface connection
- A telephone cable is attached to LINE
connection
Disable
The Auto Power Off function is disabled. The
machine will not turn off automatically.
Note
In the following cases, the Auto Power Off function is also
disabled.
- When an error occurs
- When time-set transmission is scheduled
- When the fax transmission is waiting for a redial
-When [Auto Power Off] is [Auto Config.] and
Ethernet cable is attached
-When [Auto Power Off] is [Auto Config.] and
telephone cable is attached
Memo
By factory default, the time interval to turn off the power
is set to 4 hours. You can change the time interval by
pressing the <SETTING> key on the operator panel and
then selecting [Admin Setup] > [Management] >
[Power Save] > [Auto Power Off Time].
By factory default, [Auto Power Off] is set to [Auto
Config] or [Disable]. You can change the setting by
pressing the <SETTING> key on the operator panel and
then selecting [Admin Setup] > [User Install] >
[Power Save] > [Auto Power Off]
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Oki MB491 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Oki MB491 in the language / languages: English as an attachment in your email.

The manual is 25,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Oki MB491

Oki MB491 User Manual - English - 182 pages

Oki MB491 User Manual - German - 229 pages

Oki MB491 User Manual - German - 210 pages

Oki MB491 User Manual - Dutch - 222 pages

Oki MB491 User Manual - Dutch - 200 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info