492997
52
Zoom out
Zoom in
Previous page
1/94
Next page
Menu functions > 52
FRAME TYPE AUTO / 802.2 / 802.3 /
ETHERNET II / SNAP
Applies to C331 and C531/ES5431 only.
Selects the Ethernet MAC layer frame type.
Display Condition: Netware should be enabled.
IP ADDRESS SET AUTO / MANUAL Specifies whether IP address allocation is automatic
(DHCP) or manually assigned.
IPV4 ADDRESS xxx.xxx.xxx.xxx Current assigned IP address. To change, press OK and
use Menu buttons to increment 1st octet, then press
OK again to move on to next octet. When 4th octet has
been set, press OK again to register new address.
SUBNET MASK xxx.xxx.xxx.xxx Current assigned subnet mask. To change, proceed as
above.
GATEWAY ADDRESS xxx.xxx.xxx.xxx Current assigned gateway address. To change, proceed
as above.
WEB ENABLE / DISABLE Enables or disables Web config. facility.
TELNET ENABLE / DISABLE Enables or disables Telnet config. facility.
FTP ENABLE / DISABLE Enables or disables communication via FTP.
IPSEC ENABLE / DISABLE Applies to C331 and C531/ES5431 only.
Sets Enable/Disable of IPSec. Enable via the web.
Enable: IPSec is available.
Disable: IPSec is not available.
SNMP ENABLE / DISABLE Enables or disables SNMP protocol.
NETWORK SCALE NORMAL / SMALL Selects network size.
When NORMAL is selected, printer can work effectively,
even when connected to a HUB that has a spanning
tree
feature. However, printer start up time gets longer
when computers are connected with two or three small
LANs.
When SMALL is selected, computers can cover from two
or three small LANs to a large LAN, but may not work
effectively when connected to a HUB that has a
spanning tree feature.
HUB LINK SETTING AUTO NEGOTIATE
100BASE-TX FULL
100BASE-TX HALF
10BASE-T FULL
10BASE-T HALF
Sets full or half duplex for communication via a network
hub.
When AUTO is set, negotiation is done automatically.
TCP ACK TYPE 1
TYPE2
This setting determines whether the network card in
the Printer/MFP will acknowledge every TCP packet or
whether it will delay it’s acknowledgement until
multiple packets have been received.
When Type 1 is set the Printer/MFP will respond to
every TCP packet with an ACK packet.
When Type 2 is set the Printer/MFP will delay it’s TCP
ACK response.
In most environments the default TCP ACK setting
should be OK, however changing this setting may be
beneficial when a connection problem (e.g your printing
job incompletely terminates) occurs if it takes a long
time to interpret/print your job.
FACTORY DEFAULTS EXECUTE Reloads the settings present when the unit was setup
by the manufacturer.
ITEM SETTINGS EXPLANATION
52


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Oki ES5431 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Oki ES5431 in the language / languages: English as an attachment in your email.

The manual is 12,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Oki ES5431

Oki ES5431 User Manual - German - 104 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info