665229
59
Zoom out
Zoom in
Previous page
1/104
Next page
Menu functions - C821 and C830 > 59
PS Setup Network
Protocol
ASCII/RAW Specifies PS communication protocol mode of data from
NIC port.
(In RAW mode, Ctrl-T is invalid). PS models only.
Parallel
Protocol
ASCII/RAW Specifies PS communication protocol mode of data from
Centronics port.
(In RAW mode, Ctrl-T is invalid). PS models only.
USB
Protocol
ASCII/RAW Specifies PS communication protocol mode of data from
USB port.
(In RAW mode, Ctrl-T is invalid). PS models only.
PCL Setup Font Source Resident Specifies the location of PCL default font.
Font
Number
I0 ~ I90 Sets the PCL font number.
The valid range of this variable changes depending on the
FONT SOURCE setting at the time. If the default font is
set for FONT SOURCE, the number starts at 0. If it is not,
the number starts at 1. The maximum value is equal to
the number of fonts installed in FONT SOURCE.
Font Pitch 99.99CPI
~
10.00CPI
~
0.44CPI
Width of the PCL default font in characters per inch (CPI).
Default font is fixed-pitch, scalable font.
The value of pitch is displayed down to the second
decimal place.
Displayed only when the font selected in Font No. is a
fixed-spacing, scalable font.
Symbol Set PC-8 Sets the symbol set of PCL (see machine operator panel
for complete list).
A4 Print
Width
78 column
80 column
Sets the number of characters for A4 paper.
Auto LF.
This is for 10-CPI characters when Auto CR/LF Mode is set
to OFF.
This menu is enabled only when A4 paper is selected in
the menu that sets the print width of A4 paper in portrait
orientation.
Usually, such A4 paper print width is set slightly narrower
than 8 inches (about 7.93 inches).
This setting cannot print 80 10-cpi characters (only prints
up to 78 10-cpi characters). 80 characters set at A4 Print
Width widen the right and left margins.
A PCL command selects or selects/deselects Auto CR/LF
mode.
White Page
Skip
On/Off Sets whether to eject a page without any data to print
(blank page) upon reception of FF command (OCH) in PCL
Mode. OFF: Ejecting.
CR Function CR/CR+LF Sets action when CR code is received in PCL.
CR: Carriage Return
CR+LF: Carriage Return and Line Feed
LF Function LF/LF+CR Sets action when LF code is received in PCL.
LF: Line Feed
LF+CR: Line Feed and Carriage Return
Print Margin Normal
1/5 inch
1/6 inch
Sets a non-printable area of paper.
The width of the area along the right and left sides of
paper (left and right sides depend on paper orientation).
NORMAL: PCL emulation compatible, approximately 1/
4~1/4.3INCH (depending on paper) is outside the
printable area.
ITEM SETTINGS EXPLANATION
59


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Oki C821 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Oki C821 in the language / languages: English as an attachment in your email.

The manual is 6,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Oki C821

Oki C821 User Manual - German - 115 pages

Oki C821 User Manual - Dutch - 112 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info