665201
37
Zoom out
Zoom in
Previous page
1/93
Next page
Menu functions > 37
PCL Setup Font Source Resident Specifies the location of PCL default font.
Font Number I0 ~ I90 Sets the PCL font number.
The valid range of this variable changes
depending on the Font Source setting at the
time. If the default font is set for Font
Source, the number starts at 0. If it is not,
the number starts at 1. The maximum value
is equal to the number of fonts installed in
Font Source.
Font Pitch 0.44 CPI
~
10.00 CPI
~
99.99 CPI
Width of the PCL default font in characters
per inch (CPI). Default font is fixed-pitch,
scalable font.
The value of pitch is displayed down to the
second decimal place.
Displayed only when the font selected in Font
Number is a fixed-spacing, scalable font.
Font Height 4.00 point
~
12.00 point
~
999.75 point
Height of the PCL default font. The value is
displayed down to the second decimal place
(in 0.25 point increments).
Displayed only when the font selected in Font
Number is a proportional-spacing, scalable font.
Symbol Set PC-8 Sets the symbol set of PCL (see machine
operator panel for complete list).
A4 Print Width 78 column
80 column
Sets the number of characters for A4 paper.
Auto LF.
This is for 10-CPI characters when Auto CR/
LF Mode is set to Off.
This menu is enabled only when A4 paper is
selected in the menu that sets the print width
of A4 paper in portrait orientation.
Usually, such A4 paper print width is set slightly
narrower than 8 inches (about 7.93 inches).
This setting cannot print 80 10-cpi characters
(only prints up to 78 10-cpi characters). 80
characters set at A4 Print Width widen the
right and left margins.
A PCL command selects or selects/deselects
Auto CR/LF mode.
White Page Skip On/Off Sets whether to eject a page without any data
to print (blank page) upon reception of FF
command (OCH) in PCL Mode. Off: Ejecting.
CR Function CR/CR+LF Sets action when CR code is received in PCL.
CR: Carriage Return
CR+LF: Carriage Return and Line Feed
LF Function LF/LF+CR Sets action when LF code is received in PCL.
LF: Line Feed
LF+CR: Line Feed and Carriage Return
Print Margin Normal
1/5 inch
1/6 inch
Sets a non-printable area of paper.
The width of the area along the right and left
sides of paper (left and right sides depend on
paper orientation).
Normal: PCL emulation compatible,
approximately 1/4~1/4.3 inch (depending on
paper) is outside the printable area.
ITEM SETTINGS EXPLANATION
37


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Oki C712 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Oki C712 in the language / languages: English as an attachment in your email.

The manual is 4,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Oki C712

Oki C712 User Manual - German - 99 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info