665196
40
Zoom out
Zoom in
Previous page
1/131
Next page
- 40 -
2. Setting Up
When [WPS connection successful.] is displayed, select [Close] and press the
(Enter) button.
When [Connection failed. Timeout] is displayed, repeat the procedure from step 14.
[Overlap] is displayed when multiple WPS push buttons are pressed almost at the same time at two or more
wireless LAN access points and connection is not established. Wait for a while, and then try again.
15
If the antenna mark is displayed at the top right of the home screen, the
connection is established correctly.
The antenna mark may not be displayed on some screens.
Selecting a Wireless LAN Access Point from the Operator Panel to Connect
If a wireless LAN access point does not support WPS, you can specify a wireless LAN
access point you want to use from the wireless LAN access points that the machine detects
to establish a connection. In such a case, you must enter an encryption key.
1
Check the SSID and encryption key by referring to the instruction manual that
is included in a wireless LAN access point or other documents, and write the
information down.
WPA-EAP and WPA2-EAP cannot be set on the touch panel. Set them from the Web page of this machine.
Open the Web Page of This Machine (Advanced Manual)
An SSID is also called a network name, ESSID or ESS-ID.
An encryption key is also called a network key, security key, password or Pre-shared Key.
2
Check that the wireless LAN access point starts and is operating properly.
3
Turn the machine on.
Check that the screen displays "Do you want to Set-up wireless?" and [Yes] is selected, Press the (Enter)
button and go to step 6.
4
Press the button repeatedly to select [Setting] and press the (Enter)
button.
5
Press the button repeatedly to select [Wireless(Infrastructure) Setting] and
press the (Enter) button.
6
Enter the administrator password, and then press the (Enter) button.
The factory default administrator password is "999999". If the administrator password is
changed, enter the updated password.
The [It is not possible to use the Wireless(AP Mode) at the same time.] message is
displayed for approximately five seconds.
7
Select [Enable] and then press the (Enter) button.
8
If your environment requires to set IP address, etc. manually, press the
button to select [Network Setting], and then press the (Enter) button. If you
do not need to set manually, go to step 12.
9
Press the button to select [Manual] on the [Wireless (infrastructure)
settings] screen, and then press the (Enter) button.
10
Follow the onscreen instructions to set the IP address, subnet mask, default
gateway, and DHCP v6.
Ask your provider or network administrator about the setting value.
11
Select [Close] when the Wireless (infrastructure) settings are complete, and
then press the (Enter) button.
The screen switches automatically in a while without pressing [Close].
12
Press the button repeatedly to select [Wireless Network Selection] and
press the (Enter) button.
The machine starts searching for wireless LAN access points. Wait for a while.
13
Select a wireless LAN access point to connect, and then press the (Enter)
button.
40


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Oki C532 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Oki C532 in the language / languages: English as an attachment in your email.

The manual is 4,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Oki C532

Oki C532 User Manual - German - 135 pages

Oki C532 User Manual - Dutch - 134 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info