Manual Okbaby Flat (page 4 of 37) (All languages)

773007

Zoom out

Zoom in

1/37

6.Flat Flat.7







1. Fold away Flat supports making sure that they are blocked by the lock on the side under-

neath the changing area (fig. 1).

2. Place FLAT on the cot (fig. 8), taking care to ensure that the notch is positioned over the

top-rail of the cot (fig. 14).

3. FLAT must be fixed to the top-rails of the cot by the three Velcro straps supplied, one at

the back and two at the front of the changing table.

4. Thread the strap through the slot on the bottom edge of the changing table (fig. 9), pass it

under the top-rail of the cot and secure with Velcro (fig.10). Repeat for the other two an-

chor points.



• Before proceeding to use the product on a home cot, make sure that it is perfectly sup-

ported by the two top rails and that it is fastened securely with the three straps provided.

Verify the stability of FLAT before resting your child there.

• The straps provided should only be used for securing the changing table to the baby’s cot

and should be immediately removed afterwards to avoid risk of entangling or obstruction.

• If the cot has adjustable top-rails, make sure that these are completely locked into place

before using FLAT.

• Do not move FLAT with the baby on it.



• Always be aware of the risks associated with open flames or other sources of high heat,

such as electric hot plates, gas flames, etc., close to the changing table.

• FLAT is designed for babies with a max. weight of 15 kg.

• Do not use FLAT if anything appears to be broken or missing.

• Clean FLAT with a soft cloth and a neutral detergent. Do not use abrasive cleaners, sol-

vents or ammonia-based products.

• Any optional or spare parts must be ordered from the manufacturer or distributor.









 











Product dimensions: 66.2 cm x 84.6 cm x 18.3 cm.





1. Fold away Flat supports making sure that they are blocked by the lock on the side under-

neath the changing area (fig. 1).

2. Place FLAT on a flat, stable surface (fig. 2).

3. Make sure that all the non-slip feet (fig. 3) are touching the table or work surface to ensu-

re maximum stability.



• FLAT cannot be positioned on all types of table.

Do not use it on tables with sliding tops, fold-away tables, single-leg tables, games tables

or collapsible tables.

• Do not place towels or other items on the supporting surface that may interfere with the

proper functioning of the non-slip feet. Make sure the structure and the surface of the ta-

ble are kept clean and dry.

• Do not move FLAT with the baby on it.





1. Release the side lock underneath the changing area to free FLAT supports (fig. 4).

2. Open FLAT supports completely, making sure that the red clasps hook completely into

place on the sides of the changing table (fig. 5).

3. Adjust the feet of each Flat support to the minimum width (fig.11).

4. Position FLAT over the bathtub to rest on the side edges (fig. 6).

5. Adjust the feet of the supports so that the non-slip rubber pads rest against the inside

wall of the bathtub and the suction cups rest on the top of the bathtub edges (fig. 7).

6. To close FLAT supports, press the sides of each red hook (fig. 5) pushing the changing

table’s supports inward and hook them in place on the side lock underneath the changing

area (fig. 1).



•

Make sure that the internal width of the bathtub, as shown in fig.15, measures at least 56 cm.

• Always check that the changing table is in the correct position on the bathtub and that

the fixing devices are correctly adjusted before placing the baby on the changing table.

• Position FLAT over the bathtub so that the baby cannot reach the taps.

• If the bathtub is not positioned against a wall, place FLAT centrally over it (fig. 13).

• Other children must not be allowed in the bathtub while the changing table is in position

for use.

• Do not move FLAT with the baby on it.



Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Okbaby Flat in the language / languages: All languages as an attachment in your email.

The manual is 1.14 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Okbaby Flat Manual

Product: