644317
18
Zoom out
Zoom in
Previous page
1/27
Next page
18
EN
INSTALLATION
Note: The dishwasher is equipped with power cord and plug. Make sure before installation that the wall
outlet is at the desired place of installation.
Consider the dimension of the product for placing and installation.
1
Place the dishwasher on an even, horizontal and steady surface.
Note: The dishwasher is not intended to be built in.
2
The dishwasher must be connected to drainage.
1. The hose is already connected the waste water outlet. Cut the straps and unwind the hose.
2. Connect the end to a drainpipe (Option A oder B). Observe the max. height of the outlet of
drainage hose.
Note:
A suitable hose holder is available as optional accessories.
3
Connect the water inlet to tap water supply (3/4”) using the provided hose and make sure it
fastened tightly.
Note: If the water pipes are new or have not been used for an extended period of time, let the
water run to make sure that the water is clear and free of impurities. If this precaution is not taken,
there is a risk that the water inlet can get blocked and damage the appliance.
4
Connect the power plug to the mains.
PREPARATION
Putting salt into the salt container
5
Depending on your tap water hardness (hardness degree) use additional salt (water softener).
Always consider instruction provided with the salt.
1. Remove the basket and then unscrew and remove the cap from the salt container.
2. Before rst wash, add 1.5 lt. of water in the salt container of your machine.
3. Place the end of the funnel (supplied) into the hole and introduce about 1.5 kg of salt. It is
normal for a small amount of water to come out of the salt container.
4. After lling the container, screw the cap tightly back clockwise.
5. Immediately after lling the salt into the salt container, a washing program should be started
(rapid program suggested). Otherwise lter system, pump or other important parts of the
machine may be damaged by salty water which is out of warranty.
Note: Depending on how fully the salt dissolves, the salt warning light may still be on even though
the salt container is lled.
Warning!
• Only use salt specically designed for use in dishwashers! All other types of salt not specically
designed for use in a dishwasher, especially table salt, will damage the water softener. In case of
damages caused by the use of unsuitable salt the manufacturer does not give any warranty nor is
liable for any caused damages.
• If there are spills of the salt, a soak or a rapid program should be run to remove the excess salt.
• Only ll with salt just before starting one of the complete washing programs. This will prevent any
grains of salt or salty water, which may have been split, remaining of the bottom of the machine for
any period of time, which may cause corrosion.
• The salt container must only be relled when the salt warning light in the control panel comes on.
IM_ODW60032_160118_V04_HR.indb 18 18/1/16 2:00 PM
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for OK ODW 60032 FS A2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of OK ODW 60032 FS A2 in the language / languages: English, German as an attachment in your email.

The manual is 8,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info