644316

OK ODW 45032 BI A2 Manual

19
Zoom out
Zoom in
Previous page
1/29
Next page
19
EN
INSTALLATION
1
The dishwasher must be installed in sucient proximity of water, sewage and electrical connection.
Note: Please check the included mounting material, brackets, screws and Velcro strip for attaching
the decorative panel, etc.
1
Observe the installation dimensions.
• A location near the sink is recommended for the dishwasher to be connected to water and
sewage connections easier.
• At the back of one or both lateral cupboards recesses of size 80 x 100 mm must be tted for
water, sewage and electrical connection (A).
2
If the dishwasher is installed in a corner, a minimum clearance of 50 mm between the opened door
and surrounding cabinets must be respected.
3
Note the dimensions, holes and cutouts of the decorative plate.
4
Pull apart the supplied Velcro strips and remove the protective strips. Stick the 4 Velcro strips in the
recesses of the door and the decorative plate. Align the decor panel and attach it to the door of the
dishwasher.
5
Remove the 4 lower screws.
6
Screw the supplied 4 long screws through the door and fasten the decorative plate.
7
The springs of the dishwasher door are set correctly at the factory.
• After installation of the decorative plate, the spring force of the door may have to be adjusted.
• Twist the adjusting screws on both sides to increase/decrease the spring force. Please refer to the
illustration in addition to the screws.
• The spring force is adjusted correctly when the fully open door remains in a horizontal position
and can be moved by slight train all the way up.
8
Stick the condensation strip below of the worktop. Make sure that it is closed with the front edge of
the countertop.
9
The dishwasher must be connected to drainage.
1. The hose is already connected the waste water outlet. Cut the straps and unwind the hose.
2. Connect the end to a drainpipe (Option A oder B). Observe the max. height of the outlet of
drainage hose.
Note: A suitable hose holder is available as optional accessories.
10
Connect the water inlet to tap water supply (3/4”) using the provided hose and make sure it
fastened tightly.
Note: If the water pipes are new or have not been used for an extended period of time, let the
water run to make sure that the water is clear and free of impurities. If this precaution is not taken,
there is a risk that the water inlet can get blocked and damage the appliance.
11
Connect the power plug to the mains.
12
The dishwasher must be placed in the installation position so that it is absolutely level.
• The rear stand can be adjusted by turning the middle Phillips screw (Pos. A) in height. Please
refer to the gure next to the screw (UP: rear is raised, DOWN: rear is lowered).
• The front feet can be adjusted by turning by hand.
• Check the horizontal stand with a spirit level on horizontal or vertical surfaces in the interior of
the dishwasher and the door.
13
Place the dishwasher into position.
14
The dishwasher must be fastened with screws in mounting position.
Option I
Wood Countertop: Insert the mounting bracket on top of the cut-outs. Screw the mounting
bracket now with the underside of the countertop.
Option II
Natural stone countertop: Remove the plastic cap of the side walls of the dishwasher (door open).
Fasten the dishwasher laterally with the screws through the openings of the cabinets left and right
from the dishwasher.
IM_ODW60012_160118_V05_HR.indb 19 18/1/16 2:12 PM
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for OK ODW 45032 BI A2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of OK ODW 45032 BI A2 in the language / languages: English, German as an attachment in your email.

The manual is 8,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info