Manual OK ODL 43650U-TB (page 34 of 99) (English, German, French, Italian)

783170

Zoom out

Zoom in

1/99

English - 33 -

Switching On/Off

To Switch the TV On

Connect the power cord to a power source such as a

wall socket (220-240V AC, 50 Hz).

To switch on the TV from standby mode either:

• Press the Standby button, Programme +/- or a

numeric button on the remote control.

• Press the middle of the side function switch on the

TV in.

To Switch the TV Off

Press the Standby button on the remote control or

press the middle of the side function switch on the

TV in and hold it down for a few seconds, the TV will

switch into standby mode.

To power down the TV completely, unplug the

power cord from the mains socket.

Note: When the TV is switched into standby mode, the

standby LED can blink to indicate that features such as

Standby Search, Over Air Download or Timer is active. The

LED can also blink when you switch on the TV from standby

mode.

First Time Installation

When turned on for the first time, the language

selection screen is displayed. Select the desired

language and press OK.

On the next screen, set your preferences using the

directional buttons.

Note: Depending on the Country selection you may be asked

to set and conrm a PIN at this point. The selected PIN cannot

be 0000. You have to enter it if you are asked to enter a PIN

for any menu operation later.

About Selecting Broadcast Type

Digital Aerial: If Digital Aerial broadcast search

option is turned on, the TV will search for digital

terrestrial broadcasts after other initial settings are

completed.

Digital Cable: If Digital Cable broadcast search

option is turned on, the TV will search for digital cable

broadcasts after other initial settings are completed.

According to your other preferences a conrmation

message may be displayed before starting to search.

Select YES and press OK to proceed. To cancel

operation, select NO and press OK. You can select

Network or set values such as Frequency, Network

ID and Search Step. When nished, press OK button.

Note: Searching duration will change depending on the

selected Search Step.

Satellite: If Satellite broadcast search option is

turned on, the TV will search for digital satellite

broadcasts after other initial settings are completed.

Before satellite search is performed some settings

should be made. Antenna Type menu will be

displayed rst. You can select Antenna Type as

Direct, Single Satellite Cable or DiSEqC switch by

using “ ” or “ ” buttons.

• Direct: If you have a single receiver and a direct

satellite dish, select this antenna type. Press OK to

continue. Select an available satellite on the next

screen and press OK to scan for services.

• Single Satellite Cable: If you have multiple

receivers and a single satellite cable system, select

this antenna type. Press OK to continue. Congure

settings by following instructions on the next screen.

Press OK to scan for services.

• DiSEqC switch: If you have multiple satellite

dishes and a DiSEqC switch, select this antenna

type. Then set the DiSEqC version and press OK

to continue. You can set up to four satellites (if

available) for version v1.0 and sixteen satellites for

version v1.1 on the next screen. Press OK button

to scan the rst satellite in the list.

Analogue: If Analogue broadcast search option is

turned on, the TV will search for analogue broadcasts

after other initial settings are completed.

Additionally you can set a broadcast type as your

favourite one. Priority will be given to the selected

broadcast type during the search process and the

channels of it will be listed on the top of the Channel

List. When nished, press OK to continue.

You can activate Store Mode option at this point.

This option will congure your TV’s settings for store

environment and depending on the TV model being

used, the supported features of it may be displayed

on the top of the screen as an info banner. This option

is intended only for store use. It is recommended to

select Home Mode for home use. This option will be

available in System>Settings>More menu and can

be turned off/on later.

Press OK button on the remote control to continue.

After the initial settings are completed TV will start

to search for available broadcasts of the selected

broadcast types.

After all the available stations are stored, scan results

will be displayed. Press OK to continue. The Edit

Channel List menu will be displayed next. You can

edit the channel list according to your preferences or

press the Menu button to quit and watch TV.

While the search continues a message may appear,

asking whether you want to sort channels according

to the LCN(*). Select Yes and press OK to conrm.

(*) LCN is the Logical Channel Number system that organizes

available broadcasts in accordance with a recognizable

channel number sequence (if available).

Note: Do not turn off the TV while initializing first time

installation. Note that, some options may not be available

depending on the country selection.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of OK ODL 43650U-TB in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 8.95 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

OK ODL 43650U-TB Manual

Product: