568770

OK OBH 16311 Manual

15
Zoom out
Zoom in
Previous page
1/62
Next page
15
EN
INTENDED USE
This product is designed for heating and cooking foods in suitable pans or pots. Any other use may result
in damage to product or injuries.
COMPONENTS
A. Hotplate 1500 W
B. Hotplate 1000 W
C. Hotplate 2000 W
D. Hotplate 1000 W
E. Control panel
F. Power indicator light
G. Temperature controls
H. Brackets
I. Screws
J. Sealing strip
BEFORE FIRST USE
• Remove the product and accessories from the original packaging carefully. For disposal of the original
packaging, follow applicable legal requirements. If you have questions about correct disposal, contact
your local authority.
• Check the package contents for completeness and damage. If the package content is incomplete or
damages can be found, contact your place of purchase immediately.
• After unpacking clean the product, see chapter Cleaning and care.
• During the production product parts (hot plate) are coated with a protective lm. To remove these
production residues, turn the thermostat up to the maximum position (level 6) and keep the product
in operation for about 3 minutes without pot/pan. Please ensure adequate ventilation, as this can lead
to slight odor and smoke which is harmless and will disappear after a short time.
INSTALLATION
1
For installation pay attention to all dimensions. Prepare a cutout of 490 x 560 mm into the work
plate.
WARNING! Pay attention to the safety clearances to the side and rear. When installing a hob higher
cabinets or room walls are only allowed with a 60 mm distance from the rear and 55 mm distance from
only one side (right or left). There shall be no higher cabinet or wall to the other side (right or left).
2
Pay attention to minimum clearances for air circulation inside the kitchen cabinet.
A (mm) B (mm) C (mm) D E
min. 650 min. 100 min. 20 Air inlet Air outlet min. 5mm
WARNING! If a hood is placed over the hob, the safety distance specied by the manufacturer must
be observed.
If no manufacturer's instructions are available or combustible materials (e.g. a wall unit) mounted
above the hob, the safety distance A must be at least 650 mm.
3
This appliance must be earthed.
Minimum requirement power cord: H05VV-F 3x6mm
2
/3x2.5mm
2
If possible connect the hob the mains before installing the hob to the work plate.
WARNING! Before connecting, all poles of the corresponding circuit must be disconnected from
mains supply.
The corresponding circuit shall be secured against unintentional reconnection.
The electrical connection must be done by an appropriately trained professional.
1. Remove the protective cap from the terminal.
2. Pay attention to the connection diagram and connect L, N and ground to the terminal
accordingly. Make sure that all cables are rmly xed.
3. Put the protective cap back on the terminal.
IM_OBH16311_140925_V03_HR.indb 15 25/9/14 5:57 PM
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for OK OBH 16311 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of OK OBH 16311 in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish as an attachment in your email.

The manual is 3,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info