783003
27
Zoom out
Zoom in
Previous page
1/32
Next page
27
Fig. 10 Setting the timer
The timer switches the product on or into standby when a user-dened time has elapsed.
When switching on, the last mode and setting will be used. The set durations will be counted
down immediately after the input without correlation to the contrary time setting.
1. Press the timer program button TIMER at the product or the specic TIMER ON/OFF
button at the remote control to enter timer setting for either the auto-on or auto-standby
timer. The respective indicator for each setting will light up.
2. Press the / buttons or the specic TIMER ON/OFF button at the remote control as
often as necessary to set a time from 0.5 to 24 hours.
3. The setting will be saved after 5 seconds without input.
Examples:
• To have the product switched o after 1 hour and on again after another 1 ½ hours, set the
auto-o time to 1.0 h and the auto-on time to 2.5 h during operation.
• To have the product switched on after 8 hours and o after another 8 hours, set the auto-
on time to 8.0 h and the auto-o time to 16.0 h while in standby.
Notes:
• The adjusting increments are 0.5 hours up to 10 hours, then 1 hour up to 24 hours.
• The respective indicator will be lit, when a time is set.
• Switching the product on or into standby manually will cancel the timer setting.
• The timer settings will be lost once the respective actions were conducted and the time
needs to be set again.
• The timer setting will be lost in case an error occurs (see protection and error codes).
Preprogramming a function
By pushing the SHORTCUT button any function and temperature can be saved and recalled.
1. Choose your desired function e.g. using the MODE, TEMP / or / and FAN buttons, etc.
2. Press and hold SHORTCUT button until the display ashes one time to save the setting.
3. The preset setting can be recalled anytime and from any mode by simply pushing the SHORTCUT
button.
Fig. 11 WATER DRAINAGE
Water is only collected during automatic AUTO, cooling and dehumidifying mode .
During dehumidifying mode water is drained immediately through the upper drain outlet
and the drainage hose must be continuously connected. The water is drained through the
hose into a suitable container or nearby drain.
WARNING – Danger of ooding! Do not leave the product unattended when draining to an
external container! Empty the container frequently to avoid spilling over and water damage.
During automatic AUTO and cooling mode water is collected in an internal tank, which
must be drained when full. In this case the product will emit an audible signal, while the
display on the control panel is showing the protection code P1. The cooling process will stop
until the water is drained and the product restarted, while the fan remains running.
1. Disconnect the product from the power supply.
2. Place the product with the lower drain outlet above a suitable container or a drain.
3. Remove the cover of the lower drain outlet.
4. Attach the cover of the outlet again, when all water is drained.
5. Connect the plug to a suitable socket.
6. The product is ready to be switched on.
IM_OAC2221_161201_V04_HR.indb 27 1/12/16 4:31 PM
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for OK OAC 2221 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of OK OAC 2221 in the language / languages: English, German as an attachment in your email.

The manual is 4.52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info