642099
33
Zoom out
Zoom in
Previous page
1/76
Next page
33
8. UMSTELLUNG AUF EINE
ANDERE GASART
8.1 Umstellung von Erdgas auf Propan-
gas
Für die Umstellung von Erdgas auf Butan-/Propangas ist
nur eine Einstellung des Brenners erforderlich.
Die Brennereinstellung erfolgt durch die Kontrolle des
CO2-Gehalts der Abgase bei maximaler Leistung.
Den Betriebsschalter auf „0“ stellen.
Zur Voreinstellung des Brenners: Die Einstellschrau-
be 3 Umdrehungen nach rechts drehen (oder
die Schraube bis zum Anschlag drehen und
dann 3 Umdrehungen lösen).
Den Betriebsschalter auf „I“ stellen. Der Brenner
geht in Betrieb.
Den Heizkessel auf maximale Leistung bringen.
- Taste drücken und Brennerleistung mit dem
Dreh-Einstellungsknopf einstellen.
= maximale Leistung
Den Kunststoffstopfen vom Messstutzen entfer-
nen.
Den CO
2
-Gehalt der Abgase mit einem Messgerät
messen.
Den CO
2
-Gehalt der Abgase an der Einstellschraube
auf 10,5 %, ±0,3% mit Hilfe der Stellschraube
einstellen:
- Lösen = Erhöhung des CO
2
-Gehalts
- Anziehen = Verringerung des CO
2
-Gehalts
Wenn die Einstellung in Ordnung ist, die Klappe des
Schaltfeldes schließen.
Den Betriebsschalter auf „0“ stellen.
Das Messgerät entfernen und den Kunststoffstopfen
am Stutzen anbringen.
8.2 Aufkleben des Etiketts "Gasart"
Das Etikett mit der Angabe der Gasart, für die der Kessel
ausgelegt und eingestellt ist, aufkleben.
8.3 Eventuelle Montage eines externen
Magnetventils
Bei der Installation ab 1 Meter Erdgleiche ist ein externes
Magnetventil in unmittelbarer Nähe der Gebäude- oder
Raumeinführung in die Gaszuleitung einzubauen.
Der Elektroanschluss erfolgt am Schaltfeld des Heizkes-
sels.
1
8538N056A
2
8538N061
1
1
2
1
2
8538N
077
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Oertli OPTIMAT GVR 140-25 Condens at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Oertli OPTIMAT GVR 140-25 Condens in the language / languages: German as an attachment in your email.

The manual is 5,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info