642099
29
Zoom out
Zoom in
Previous page
1/76
Next page
29
7. INBETRIEBNAHME
7.1 Prüfungen vor der Inbetriebnahme
Die erste Inbetriebnahme muss von einem
Fachmann durchgeführt werden.
Vor der Inbetriebnahme muss die Heizungsanlage voll-
ständig entleert und gespült werden (Siehe “WICHTIGE
HINWEISE BEZÜGLICH DER HEIZKREISLAUF-WAS-
SERAUFBEREITUNG”, Seite 18)
7.2 Befüllung der Anlage
Anlage befüllen und entlüften.
Kappe des Wassereinfüllstutzens vom Kondens-
wassersiphon abschrauben.
Kondenswassersiphon befüllen.
Der Betrieb ohne gefüllten Kondenswassersiphon
kann zu Beschädigungen des Heizkessels führen.
Kappe des Wassereinfüllstutzens wieder auf den
Kondenswassersiphon aufschrauben.
Druck der Anlage am Manometer überprüfen: Min-
destdruck 0,5 Bar.
Die wasserseitige Dichtigkeit prüfen.
Wasserdruck der Anlage prüfen; diese ist am Display
des Schaltfeldes ausgewiesen:
Druck unzureichend: Wasser hinzufügen
(0 – 0,5 Bar)
Hinzufügen von Wasser empfohlen (0,5 – 1 Bar)
Druck in Ordnung (1 – 2 Bar)
Druck zu hoch (> 2 Bar)
Mindestdruck bei kalter Anlage = 2 Segmente.
Falls erforderlich Wasser nachfüllen.
7.3 Einstellung der Kesselleistung zur
Emissionsmessung und STB-Test
Regelung-Abdeckblende öffnen.
Taste drücken und Brennerleistung mit dem
Dreh-Einstellungsknopf einstellen.
: Maximale Kesselleistung
: Maximale eingestellte Heizleistung
: Mindest Leistung
Im Display werden Abwechselnd (alle 2 Sekunden)
folgende Werte angegeben:
EMISSION MES. : Brennergebläse-Drehzahl in
U/Min.
EMISSION MES. : Kesseltemperatur in °C
EMISSION MES. : Ionisationsstrom in µA
STB-TEST
Um den STB-TEST durchzuführen, die Taste wäh-
rend 5 Sekunden, betätigen: STB-TEST erscheint im
Display.
8539N021
1
1
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Oertli OPTIMAT GVR 140-25 Condens at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Oertli OPTIMAT GVR 140-25 Condens in the language / languages: German as an attachment in your email.

The manual is 5,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info