551847

Oceanic OCI Manual

64
Zoom out
Zoom in
Previous page
1/76
Next page
64
OCi OPERATING MANUAL
© 2002 Design, 2013 Doc. No. 12-5335-r02 (9/12/13)
REFERENCE MENU, information includes (Fig. 164):
> Graphic SEL, with selections >>
> SET HEADING -
To access Set Reference Heading..
> REVERSE -
To access Reverse Heading (to change the Reference Heading set by
180°
).
> On time remaining, counting down, if 15 to 0 (sec).
• S (2 sec) - to step back to the Compass OP Main.
• A or M (< 2 sec) - to toggle between the selections.
• S (< 2 sec) - to select that item.
• M (2 sec), at any time - to revert to the Compass OP Main.
• L (< 2 sec) - to toggle the Backlight On/Off.
• L (2 sec), while the Backlight is On - to reset the timer and keep it On for the duration time set.
SET REFERENCE HEADING, information includes (Fig. 165):
> Current Depth with FT (or M) icon, blank on the surface.
> Reference Mode icon (2 bars with up arrow), with the graphic SET above it (fl ashing upon access).
> Static Arrow icon (at 12 o'clock), diver direction of travel.
> Dynamic (moving) Arrow, tracking Reference direction currently set.
> Numeric heading (diver's direction) at lower/right with position graphic.
> On time remaining, counting down, if 15 to 0 (sec).
• S (2 sec) - to step back to the Reference Menu.
• S (< 2 sec) - to fl ash the numeric Heading value (lower/right), with SET solid.
• Rotate the Compass (keeping it level) in either direction to the new Heading, numeric displayed at the lower/right.
• S (< 2 sec) - to lock in the new Heading, with the numeric replacing the graphic SET.
• M (2 sec), at any time - to revert to the Compass OP Main.
• L (< 2 sec) - to toggle the Backlight On/Off.
• L (2 sec), while the Backlight is On - to reset the timer and keep it On for the duration time set.
REVERSE REF HEADING, information includes (Fig. 166):
> Current Depth with FT (or M) icon, blank on the surface.
> Reverse Mode icon (2 bars with down arrow) with the reverse Heading (180° opposite of the Reference Heading set) above
it, fl ashing.
> Static Arrow icon (at 12 o'clock), diver direction of travel.
> Dynamic (moving) Arrow, tracking the Reference direction currently set.
> Numeric heading (diver's direction) at lower/right, with position graphic.
> On time remaining, counting down, if 15 to 0 (sec).
• S (2 sec) - to step back to the Reference Menu.
• S (< 2 sec) - to reverse and save the new Reverse Heading, numeric solid, and revert to the Reverse OP Main.
The value at the lower/right will then indicate actual current direction.
• M (2 sec), at any time - to revert to the Compass OP Main.
• L (< 2 sec) - to toggle the Backlight On/Off.
• L (2 sec), while the Backlight is On - to reset the timer and keep it On for the duration time set.
CALIBRATION (surface only)
Local magnetic fi elds can effect display of actual location when reading a digital compass. It may be advantageous to Calibrate
the Compass before its fi rst use after purchase, prior to use in a new region, or if inaccuracies are experienced. Calibration will
be required when the battery is changed.
Upon selecting Calibrate on the Compass Main Menu, a Start screen* is displayed, information includes (Fig. 167) -
> Graphics CAL and ROTATE TO CALIBRATE.
> 360 with ° icon.
*The Start screen will also be displayed after the Battery is changed and Data is either saved or cleared.
• S (< 2 sec) - to activate (start) Calibration.
• S (2 sec) - to step back to the Compass Main Menu.
• Slowly and steadily rotate the unit 360° in either direction while maintaining it in a fl at level position (keeping it level is
critical for acurracy), CAL progress will be displayed by a dotted circle forming in the center of the screen (Fig. 168).
Rotation should take about 30 seconds. If not fully rotated in 60 seconds, operation will revert to the Compass Main Menu.
Upon completion, the graphics CAL with PASSED READY or AGAIN FAILED will fl ash for 3 seconds (Fig. 169A/B), then -
>> If READY, operation will reverts to the Compass OP Main.
>> If FAILED, operation will revert to the Start (CAL ROTATE) screen for repeat.
After 3 attempts, operation will revert to the
Watch or Surface Main and the previous successful Calibration will remain in effect.
Fig. 165 - SET REFERENCE
HEADING
Fig. 166 - REVERSE REF
HEADING
Fig. 167 - START CAL
Fig. 168 - PROGRESS
(turn until full circle)
Fig. 169B - CAL FAILED
Fig. 169A - CAL PASSED
Fig. 164 - REF MENU
… 64 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Oceanic OCI at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Oceanic OCI in the language / languages: English as an attachment in your email.

The manual is 2,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Oceanic OCI

Oceanic OCI User Manual - German - 76 pages

Oceanic OCI User Manual - French - 76 pages

Oceanic OCI User Manual - Italian - 76 pages

Oceanic OCI User Manual - Spanish - 76 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info