47525

Oce OP20 Operations Guide Printing System Functions Manual

61
Zoom out
Zoom in
Previous page
1/87
Next page
4-4
4. Printer Driver for WindowsNT
■ Media:
Saves on toner. Setting can be made in the “Change ‘Media’ Setting” area. The factory default setting is “Off”.
■ Paper/Output:
Allows you to select the location of ejection and whether you want to staple the sets or not when the optional Job Separator or Finisher is
installed. Selection can be made in the “Change ‘Paper/Output’ Setting” area.
[Inner Tray] .................................Copies will be ejected onto the Inner tray.
[Job Separator] .........................Copies will be ejected into the optional Job Separator.
[Finisher (Staple Off)] ...............Copies will be ejected into the optional Finisher. (Only available in the 20 ppm copiers)
[Finisher (Staple On)]................Copies will be stapled and ejected into the optional Finisher. (Only available in the 20 ppm copiers)
* Paper sizes are acceptable for use with the Job Separator are as follows:
Paper sizes: Letter (8 1/2" x 11"), Legal (8 1/2" x 14"), Ledger (11" x 17"), Statement (5 1/2" x 8 1/2"), A3, A4, A5, Folio (210 mm x 330
mm), JIS B4 and JIS B5
* Paper sizes and source of paper feed that are acceptable for use with the Finisher are as follows:
Paper sizes: Letter (8 1/2" x 11"), Legal (8 1/2" x 14"), Ledger (11" x 17"), A3, A4, Folio (210 mm x 330 mm), JIS B4 and JIS B5
Source of paper feed: Any tray EXCEPT the Bypass Tray
* Paper sizes and source of paper feed that are acceptable for stapling are as follows:
Paper sizes: Letter (8 1/2" x 11"), Legal (8 1/2" x 14"), Ledger (11" x 17"), A3, A4, JIS B4 and JIS B5
Source of paper feed: Any tray EXCEPT the Bypass Tray
Note
If you want to staple your printed sets, be sure to use a Collator driver. (Refer to “Collator driver” on page 1-1.)
■ Print Quality (Management Code)
This setting is used when Copy Management is turned ON in the printer. If the “management code” selected in the “Change ‘Print Quality’
Setting” area does not match the one set on the printer, printing will not be performed. If “Management Code Off” is selected, the number
of prints for each department will not be checked. The factory default setting is “Management Code Off”.
* If Copy Management is turned ON and this setting does not match the setting made in the printer itself, it will not be possible to make
test prints. Thus, when you install the printer driver, you will need to check the Copy Management settings and make a test print AFTER
the installation procedure is complete.
* When Copy Management is turned ON, even if you send a print command with a DOS “COPY” command, printing will not be possible
if you do not use a printer driver.
4-4 Document Options (Universal Driver)
… 61 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Oce OP20 Operations Guide Printing System Functions at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Oce OP20 Operations Guide Printing System Functions in the language / languages: English as an attachment in your email.

The manual is 1,51 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info