47525

Oce OP20 Operations Guide Printing System Functions Manual

44
Zoom out
Zoom in
Previous page
1/87
Next page
2. Windows XL Driver
2-6
2-5 Output Tab
■ Output to:
Specifies the location of ejection of printed copies.
Selection is possible when the optional Job Separator and or Finisher are installed.
[Inner Tray] .................................Copies will be ejected onto the Inner tray.
[Separator Tray] .........................Copies will be ejected into the optional Job Separator.
[Finishing Tray] ..........................Copies will be ejected into the optional Finisher. (Only available in the 20 ppm copier)
* In order to set the location of ejection for the Job Separator or Finisher, it is necessary to first perform the setting for that optional
equipment under “Device Options” on page 2-7.
* Paper sizes and types that are acceptable for use with the Job Separator are as follows:
Paper sizes: Letter (8 1/2" x 11"), Legal (8 1/2" x 14"), Ledger (11" x 17"), Statement (5 1/2" x 8 1/2"), A3, A4, A5, Folio (210 mm x 330
mm), JIS B4 and JIS B5
Paper types: Plain, Letterhead, Recycled and Color
* Paper sizes, types and source of paper feed that are acceptable for use with the Finisher are as follows:
Paper sizes: Letter (8 1/2" x 11"), Legal (8 1/2" x 14"), Ledger (11" x 17"), A3, A4, Folio (210 mm x 330 mm), JIS B4 and JIS B5
Paper types: Plain, Letterhead, Recycled and Color
Source of paper feed: Any tray EXCEPT the Bypass Tray
■ Copies
Specifies the number of prints to be made. Select between 1 and 999 copies by clicking on the arrows at the right of the field or by typing
the desired number directly into the field. The factory default setting is “1”.
■ Collate
When you are printing more than one copy of one or more pages, it is
possible to sort the printed copy sets.
* It is necessary to create a RAM disk. (Refer to “RAM disk” on page 2-7)
* If you select to turn on the “Staple” setting below, it is necessary to
select “Collate” here.
Example: If the “Collate” option is selected, it is possible to print out
2 sets of the same copies.
■ Staple
Stapling is possible if the optional finisher is installed.
* Stapling is only available with 20 ppm copiers.
* The following settings are required before stapling is possible:
(1) “Device Options” setting in the “Device Settings” Tab
Select “Internal Finisher” and “RAM Disk”.
(2) “Output” Tab
Select “Finishing Tray” as the “Output to” setting and select “Collate” as well.
* Paper sizes, types and source of paper feed that are acceptable for stapling are as follows:
Paper sizes: Letter (8 1/2" x 11"), Legal (8 1/2" x 14"), Ledger (11" x 17"), A3, A4, JIS B4 and JIS B5
Paper types: Plain, Letterhead, Recycled and Color
Source of paper feed: Any tray EXCEPT the Bypass Tray
Note
The location of the staples will depend upon the orientation of the paper and the direction of the printed image. Thus, when you click on
either of the options (“Upper Left” and “Upper Right”) a message will be displayed in order to verify the orientation of the paper.
… 44 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Oce OP20 Operations Guide Printing System Functions at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Oce OP20 Operations Guide Printing System Functions in the language / languages: English as an attachment in your email.

The manual is 1,51 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info