Manual Oce OP15 Operations Guide Printing System Functions (page 56 of 87) (English)

47516

Zoom out

Zoom in

1/87

3-10

3. Printer Driver for Windows 95/98

● Staple

It is possible to staple your copy sets if the optional Finisher is installed.

* Stapling is only available with 20 ppm copiers.

* The following settings are required before stapling is possible:

(1) “Installable Options” setting in the “Device Options” Tab

Select “Finisher” as the “Output Device” setting and “RAM Disk” under “Optional Disk”.

(2) “Printer Features” setting in the “Device Options” Tab

Select “Finisher” as the “Paper Destination” setting and “Temporary” under “Job Spooling”.

* Paper sizes, types and source of paper feed that are acceptable for stapling are as follows:

Paper sizes: Letter (8 1/2" x 11"), Legal (8 1/2" x 14"), Tabloid (11" x 17"), A3, A4, JIS B4 and JIS B5

Paper types: Plain, Letterhead, Recycled and Color

Source of paper feed: Any tray EXCEPT the Bypass Tray

● Management Code

This setting is used when Copy Management is turned ON in the printer. If the Management code that you selected from the dropdown

list here and that selected in the printer itself do not match, printing will not be possible.

* If Copy Management is turned ON and this setting does not match the setting made in the printer itself, it will not be possible to make

test prints. Thus, when you install the printer driver, you will need to check the Copy Management settings and make a test print

AFTER the installation procedure is complete.

* When Copy Management is turned ON, even if you send a print command with a DOS “COPY” command, printing will not be possible

if you do not use a printer driver.

● Edge Smoothing

Turning this setting “On” allows the jaggies that appear around the edge of text and graphics to be evened out through the smoothing

process.

● Page Policy

Perform this setting in conjunction with the settings to be made under “Paper source” on page 3-6.

[Auto Size Select] ......................Select this setting when you want to select the source of paper feed according to the type of paper

(you are going to select “AutoSelect Tray” under “Paper source”).

[Cassette Base] .........................Select this setting when you want to select the source of paper feed according to the tray under

“Paper source”.

* If you are going to select “AutoSelect Tray” under “Paper source”, be sure to select “Auto Size Select” here or there is a possibility that

printing will be accomplished onto paper that is difference the expected.

● Job Spooling

When you want to print out more than one set of the same documents, it is possible to have them sorted and ejected one set at a time.

[None] .........................................Does not sort.

[Temporary] ............................... Sorts and prints in order of sets: Set 1, Set 2, Set 3, etc.

* It is necessary to create a RAM disk. (Refer to “● Optional Disk” below.)

* If you selected any of the “Staple” settings above, it is necessary to select “Temporary” here.

■ Installable options

Perform the settings here whenever you add optional equipment. The functions of the optional equipment will only be available to the

printer after you have completed the setting here. Select the desired optional equipment here and then change the setting in the field

under “Change setting for: xxxx”. The optional equipment available for selection are as follows:

● Optional Feeder

Perform this setting according to the installed Option Cassette.

● Output Device

Perform this setting when the optional Job Separator or Finisher (only available with 20 ppm copiers) are installed.

● Duplex Unit

Perform this setting when the optional Duplex Unit (only available with 20 ppm copiers) is installed.

● Optional Disk

Perform this setting when you want to create a RAM disk. Refer to “Chapter 1, 3-2 RAM Disk” on page 3-1 for more detailed information

on creating a RAM disk.

* In order to create a RAM disk, it is necessary to increase the memory capacity of your printer. After increasing memory, perform the

setting here according to the “VM Option” setting below.

● VM Option

Perform this setting according to the amount of memory in your printer. If a mistake is made in this setting, there is a possibility that

printing will not be accomplished properly.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Oce OP15 Operations Guide Printing System Functions in the language / languages: English as an attachment in your email.

The manual is 1,5 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Oce OP15 Operations Guide Printing System Functions Manual

Product: